Solved exercises🧮 Solve my exercise

Baccalauréat 2021 — Physics-Chemistry specialty, Asie (jour 1) remplacement — exercise 1 : Parker Solar Probe (official exam paper)

PhysicsLevel : High schoolParker Solar Probe🌐 Lire en français
Statement
PARKER SOLAR PROBE On 12 August 2018, NASA, the American space agency, launched a spacecraft toward the Sun, PSP (Parker Solar Probe), whose mission is to study the solar corona. The PSP spacecraft must meet many challenges, including: - reaching an orbit that allows it to come very close to the Sun; - protecting the measuring instruments from intense radiation. Figure 1 - PSP spacecraft (Parker Solar Probe). Description: annotated photograph of the spacecraft. At the front is a white thermal shield; radiators are placed on the side; retractable solar panels are shown; the measuring instruments fixed on the body of the spacecraft remain in the shadow cone produced by the thermal shield. Source: blogs.nasa.gov. Part 1 - The orbital characteristics of the spacecraft Since its launch on 12 August 2018, the PSP spacecraft has undergone successive changes to its orbit around the Sun due to the gravitational assistance of the planet Venus. It thus gradually reaches its optimal orbit, which will allow it to pass closest to the Sun in early 2025. The spacecraft will then make four passages at perihelion P and will be able to record a maximum amount of experimental data (figure 2 below and figure 7 in the appendix p. 16/16). Figure 2 – Path of the PSP spacecraft. Description: diagram of the orbits around the Sun, with the orbits of Mercury, Venus and Earth shown as dashed lines. Launch is indicated on 12 August 2018. A first flyby of Venus is indicated on 10 October 2018. The trajectory of the spacecraft is represented by several ellipses gradually getting closer to the Sun. The first passage at perihelion at $9,86\ R_S$ is indicated in early 2025. Source: blogs.nasa.gov. Data: - Mass of the Sun $M_S = 2,0 \times 10^{30}\ \mathrm{kg}$ - Gravitational constant $G = 6,67 \times 10^{-11}\ \mathrm{m^3\,kg^{-1}\,s^{-2}}$ 1. On figure 7 IN THE APPENDIX TO BE SUBMITTED WITH THE SCRIPT page 16/16, the elliptical orbit that the PSP spacecraft will describe around the Sun in 2025 is shown. Points A and P are respectively the aphelion and the perihelion. Point S represents the center of the Sun. 1.1. On figure 7 IN THE APPENDIX TO BE SUBMITTED WITH THE SCRIPT page 16/16 and without worrying about scale, represent the gravitational attraction force, denoted $\vec{F}_{S\to PSP}$, modelling the action exerted by the Sun on the PSP spacecraft when it is at point M. 1.2. Using Kepler’s 2nd law, compare the value $v_P$ of the spacecraft’s speed at point P with the value $v_A$ of the spacecraft’s speed at point A. 2. NASA predicts that the value $v_P$ of the spacecraft’s speed at point P will be $192\ \mathrm{km\,s^{-1}}$ with a standard uncertainty of about $5\ \mathrm{km\,s^{-1}}$. It is desired to know whether this speed value was determined using the circular-motion model for the PSP spacecraft on its orbit around the sun or whether another model was used. We therefore propose to determine the value $v$ of the PSP spacecraft’s speed by assuming that its motion is circular, with radius $r = SP = 6,9 \times 10^6\ \mathrm{km}$, in order to compare it with the value predicted by NASA (figure 3). The heliocentric frame is considered to be Galilean. Figure 3 – Circular-motion model of the PSP spacecraft and Frenet frame. Description: circular trajectory shown as dashed lines with center S; the spacecraft is at a point M on the circle. The radius $r$ connects S to M. At point M, the Frenet frame shows a tangential vector $\vec{t}$ tangent to the trajectory and a normal vector $\vec{n}$ directed toward the center S. 2.1. Using Newton’s 2nd law, show that, in the case of a circular trajectory, the speed $v$ of the PSP spacecraft is constant and has the expression: $ v = \sqrt{\dfrac{G \times M_S}{r}} $ with $M_S$ the mass of the Sun and $r$ the radius of the circular trajectory. 2.2. Calculate the value $v$ of the PSP spacecraft’s speed in this model. 2.3. Draw a conclusion regarding the issue raised in question 2. Kepler’s 3rd law relates the orbital semi-major axis and the revolution period of systems (planet, spacecraft) orbiting the Sun. The revolution period of the PSP spacecraft around the Sun can thus be determined from the measurement of the semi-major axis of its elliptical trajectory. 3. Using Kepler’s 3rd law and after analyzing the Python program below and its results, determine the revolution period $T$ of the PSP spacecraft around the Sun. Characteristics of the orbits of the planets and the PSP spacecraft around the sun: Table. Columns: Planet; Mercury; Venus; Earth; Mars; Jupiter; Saturn; Uranus; Neptune; PSP spacecraft. Line “Orbital semi-major axis ($\times 10^3\ \mathrm{km}$)” : Mercury 57909,23 ; Venus 108209,5 ; Earth 149597,8875 ; Mars 227944 ; Jupiter 778340 ; Saturn 1426700 ; Uranus 2870700 ; Neptune 4498400 ; PSP spacecraft $a = 58210$. Line “Revolution period (j) (day)” : Mercury 87,95565 ; Venus 224,667 ; Earth 365,2564 ; Mars 686,885 ; Jupiter 4332,01 ; Saturn 10754 ; Uranus 30698 ; Neptune 60216,8 ; PSP spacecraft $T$. The Python program below was written from the characteristics of the planets’ orbits. 1 import numpy as np 2 import statsmodels.api as sm 3 4 # Periods T (in d) 5 T = np.array([ 87.95565, 224.667, 365.256363, 686.885, 4332.01, 6 10754, 30698, 60216.8 ]) 7 8 # Semi-major axes a (in km) 9 a = np.array([ 57909230, 108209500, 149597887.5, 227944000, 10 778340000, 1426700000, 2870700000, 4498400000 ]) 11 12 # sm.OLS(y, x) defines a linear model of the form y = kx 13 model = sm.OLS(T**2, a**3) 14 15 # model.fit() calculates the coefficient k 16 results = model.fit() 17 18 print("--- Modelling results ---\n") 19 20 # Displays the value of the coefficient k 21 print(" k=", results.params[0], (" d**2 * km**-3") Display of the program results on the screen: --- Modelling results --- k= 3.983462498345611e-20 d**2 * km**-3 Note: the notation e-20 means $10^{-20}$. Part 2 - The photovoltaic panels During the mission, the PSP spacecraft’s photovoltaic panels provide the electrical energy needed for the operation of the onboard measuring instruments. They make it possible to obtain a useful electrical power $P_{el} = 340\ \mathrm{W}$. In 2025, when closest to the Sun, they will need to be cooled. A thermal power $P_{th}$ will then have to be removed thanks to pressurized water circulating between the photovoltaic panels and radiators (figure 4). When the shield is perfectly oriented toward the Sun, the thermal power to be removed $P_{th}$ will be 13 times greater than the useful electrical power; a thermal shield tilt error of 1° results in an additional thermal power to be dissipated of 35%. In the following questions, we consider the critical case of a 1° tilt error of the thermal shield. Data: - Density of liquid water under the pressure and temperature conditions of the PSP spacecraft: $\rho_{eau} = 0,958\ \mathrm{kg\,L^{-1}}$ - Duration of the passage near the Sun: $\Delta t = 110\ \mathrm{h}$ - Water pressure in the circuit: 5 bar - Boiling temperature of water under 5,0 bar: $T_{éb} = 150\ ^\circ\mathrm{C}$ - Specific heat capacity of water: $c_{eau} = 4185\ \mathrm{J\,K^{-1}\,kg^{-1}}$ Figure 4 – Energy diagram of the electrical supply of the PSP spacecraft. Description: solar flux arrives on a photovoltaic panel. One arrow goes out toward the electrical instruments with the mention “Useful electrical power $P_{el} = 340\ \mathrm{W}$”. Another arrow goes out toward radiators, with the mention “Thermal power $P_{th}$”; the radiators contain pressurized water and dissipate a “Dissipated power $P_d$”. 4. Knowing that the radiators can dissipate a maximum power $P_{d,max} = 6000\ \mathrm{W}$, show that these radiators can effectively dissipate the thermal power transferred by the photovoltaic panels to the pressurized water. During the duration $\Delta t$ of the passage near the Sun, the equivalent of a water volume $V_{eau} = 7570\ \mathrm{L}$ will circulate to cool the solar panels. The temperature of this volume of water will go from the value $T_{min} = 50\ ^\circ\mathrm{C}$ to a maximum value $T_{max}$ that we seek to determine. Here we consider that the thermal power received by this volume of water is $P_{th,max} = 6000\ \mathrm{W}$. 5. Give the expression for the thermal energy $Q_R$ received by the water as a function of $P_{th,max}$ and $\Delta t$. 6. Assuming that the temperature rise of the total water volume is due only to the solar panels, determine the temperature $T_{max}$ reached and determine whether or not the cooling system risks explosion. The candidate is invited to take initiatives and explain their approach even if it is not completely successful. Part 3 - The thermal shield The PSP spacecraft is protected from solar radiation by a thermal shield of surface area $S_b$ and thickness $e$ (figures 1 and 5). Constantly turned toward the Sun, this thermal shield keeps the entire body of the spacecraft at a suitable temperature so as not to damage the onboard instruments. The thermal shield is made up of an outer coating based on alumina, capable of withstanding very high temperatures up to 1900 K. Behind this coating is carbon foam, sandwiched between two rigid carbon-fiber layers, highly resistant to temperature and deformation (figure 5). Figure 5 – Simplified diagram of the thermal shield seen in cross-section. Description: cross-section of the shield, from front to back. At the front, solar radiation arrives as horizontal arrows. The alumina coating is on the front face. In the center is a thick layer of carbon foam composed of 97 % air trapped in the foam, framed by two carbon-fiber layers. The total thickness is denoted $e$. The left face is the front of the shield and the right face the back of the shield. Exposed to the intense radiation of the Sun, the temperature at the front of the shield reaches a value $T_{av} = 1700\ \mathrm{K}$ and emits a large surface thermal flux $\varphi_{av}$. Moreover, a surface thermal flux $\varphi_{ar} = 1,55\ \mathrm{kW\,m^{-2}}$ passes through the surface $S_b$ of the shield toward the back (figure 6). To ensure proper operation of the spacecraft, it is essential to limit the temperature increase at the back of the thermal shield despite this high surface thermal flux. Figure 6 – Thermal fluxes at the level of the thermal shield. Description: two vertical faces of the shield separated by thickness $e$. The front face is on the left, temperature $T_{av}$ ; the back face is on the right, temperature $T_{ar}$. A surface flux $\varphi_{av}$ is shown outward on the front side, and a surface flux $\varphi_{ar}$ passes through the shield toward the back. Data: - Thermal conductivities of some materials: Table. Material: Carbon foam ; Alumina ; Metals ; PVC. Thermal conductivity ($\mathrm{W\,m^{-1}\,K^{-1}}$) : 0,0262 ; 37 ; 20 to 400 ; 0,17. - Characteristics of the thermal shield: surface area $S_b = 16,6\ \mathrm{m^2}$ ; thickness $e = 11,4\ \mathrm{cm}$ ; thermal conductivity of the thermal shield $\lambda = 0,140\ \mathrm{W\,m^{-1\,K^{-1}}}$. - Thermal resistance $R_{th}$ of a wall of surface area $S$, thickness $e$ and thermal conductivity $\lambda$ : $R_{th} = \dfrac{e}{\lambda \times S}$ (in $\mathrm{K\,W^{-1}}$) - Thermal flux $\Phi$ crossing a wall of thermal resistance $R_{th}$ and subjected to a temperature difference $|\Delta T|$ : $\Phi = \dfrac{|\Delta T|}{R_{th}}$ 7. Characterize the mode of thermal transfer between the Sun and the PSP spacecraft. 8. Justify the use of carbon foam inside the thermal shield. 9. Determine the value of the total thermal flux toward the back $\Phi$. 10. Using the characteristics of the thermal shield and the data, determine the temperature difference $|\Delta T|$ between the two faces of the thermal shield as well as the temperature $T_{ar}$ at the back of the shield. Comment. The candidate is invited to take initiatives and explain their approach even if it is not completely successful.
⏳ Solution not generated yet

Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.

📝 See the solution

Have a similar exercise? Get it solved step by step, for free.

🧮 Solve my exercise