Baccalauréat 2022 — Physics-Chemistry specialty, Amérique du Sud (jour 2) remplacement — exercise 1 : The airbag (official exam paper)
Statement
THE AIRBAG
An airbag, or safety cushion, is a flexible membrane or envelope into which a gas is injected very rapidly by an explosive chemical transformation in order to inflate the envelope and thus absorb a shock.
Airbags are mainly used in automobiles to protect passengers during a collision and thus prevent them from suffering excessive deceleration by striking certain accessories inside the car.
Given
In laboratory experiments, acceleration is often expressed in $g$, corresponding to the value: $g = 9.81\ \mathrm{m\cdot s^{-2}}$.
Part 1. Study of an RC circuit and application to a shock detector
Airbags are triggered by an electronic chain using an acceleration sensor, such as the MEMS (Micro-Electro-Mechanical-System) accelerometer.
The aim of this part is to show that a MEMS behaves like an RC circuit.
1. We consider the response of an RC circuit subjected to an input signal $u_G(t)$ in the form of a square wave.
This square-wave voltage alternates between the values $E$ and $0\ \mathrm{V}$, and its period is denoted by $T$. The diagram in figure 1 provides a representation.
[Figure 1: on the left, representation of a square-wave signal $u_G(t)$ as a function of $t$: $u_G=E$ from $t=0$ to $T/2$, then $u_G=0$ from $T/2$ to $T$, then the pattern repeats. On the right, electrical diagram of a series circuit consisting of a generator delivering $u_G(t)$, a capacitor of capacitance $C$, then a resistor $R$. The voltage across the capacitor is denoted by $u_C(t)$, the voltage across the resistor by $u_R(t)$, and the current $i(t)$ flows in the direction from the capacitor toward the resistor.]
[Figure 2: simulated time evolution of the voltages $u_G(t)$, $u_C(t)$ and $u_R(t)$. Horizontal axis: $t$ in seconds from $0.0$ to $1.6\ \mathrm{s}$. Vertical axis: voltages in volts from $-6.0$ to $6.0\ \mathrm{V}$. The voltage $u_G(t)$ is a square wave of value $5\ \mathrm{V}$ from $0$ to $0.5\ \mathrm{s}$, $0\ \mathrm{V}$ from $0.5$ to $1.0\ \mathrm{s}$, $5\ \mathrm{V}$ from $1.0$ to $1.5\ \mathrm{s}$, then $0\ \mathrm{V}$ afterwards. A curve labeled 1 starts at about $5\ \mathrm{V}$ at $t=0$ and decreases exponentially toward $0\ \mathrm{V}$ until $0.5\ \mathrm{s}$, then takes about $-5\ \mathrm{V}$ at $0.5\ \mathrm{s}$ and increases exponentially toward $0\ \mathrm{V}$ until $1.0\ \mathrm{s}$; the pattern repeats at $t=1.0\ \mathrm{s}$. A curve labeled 2 starts at $0\ \mathrm{V}$ at $t=0$ and increases exponentially toward $5\ \mathrm{V}$ until $0.5\ \mathrm{s}$, then decreases exponentially toward $0\ \mathrm{V}$ until $1.0\ \mathrm{s}$; the pattern repeats at $t=1.0\ \mathrm{s}$.]
1.1. Using figure 2, determine the value of $E$ and that of the frequency $f$ of the square-wave voltage $u_G(t)$.
1.2. Establish the expression for the current intensity $i(t)$ flowing in the circuit as a function of $C$ and of $\dfrac{\mathrm{d}u_C(t)}{\mathrm{d}t}$.
1.3. At $t=0\ \mathrm{s}$, the voltage $u_G(t)$ changes from $0\ \mathrm{V}$ to $E$. The capacitor is initially uncharged. In this question, we study the charging phase of the capacitor between $t=0\ \mathrm{s}$ and $t=\dfrac{T}{2}$.
1.3.1. Establish the differential equation satisfied by the voltage $u_C(t)$ across the capacitor when $u_G(t)=E$.
1.3.2. Verify that $u_C(t)=E\left(1-\exp\left(-\dfrac{t}{RC}\right)\right)$ is a solution of the differential equation.
1.3.3. Starting from the expression of $u_C(t)$, show that $u_R(t)=E\exp\left(-\dfrac{t}{RC}\right)$.
1.4. Match curves 1 and 2 in figure 2 with the voltages $u_C(t)$ and $u_R(t)$. Justify your answer.
1.5. The time evolutions of these voltages were simulated with $C=1\ \mathrm{\mu F}$. Estimate the value of the resistance $R$ by explaining the method.
2. The MEMS accelerometer consists of a movable part which, when subjected to an acceleration, causes the common plate of the two capacitors to move. In the absence of acceleration, each capacitor has a capacitance $C$. We consider a displacement of the MEMS accelerometer along Ox; when it is subjected to an acceleration, their capacitances take the values $C_1$ and $C_2$ respectively, as shown in the diagrams in figure 3.
[Figure 3: principle diagrams of the MEMS accelerometer. On the left, "stationary MEMS": a horizontal movable part is connected to two springs, the $x$-axis is oriented to the right, the origin $0$ is at the center. Two parallel-plate capacitors of capacitance $C$ are formed with a fixed part; the two distances between plates are identical and denoted by $e$. One of the four plates has an area $S$. On the right, "accelerated MEMS": the acceleration is oriented to the right; the movable part is shifted so that the distance for the left capacitor is $e_1$ and that for the right capacitor is $e_2$, with $e_1
⏳ Solution not generated yet
Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.
📝 See the solutionHave a similar exercise? Get it solved step by step, for free.
🧮 Solve my exercise