Solved exercises🧮 Solve my exercise

Baccalauréat 2023 — Physics-Chemistry specialty, La Réunion — exercise 3 : Shale gas extraction by electro-fracturing (official exam paper)

PhysicsLevel : High schoolShale gas extraction by electro-fracturing🌐 Lire en français
Statement
Electro-fracturing is a method currently being studied to replace hydraulic fracturing and extract shale gas. Two electrodes are introduced into a cavity in the rock, filled with water. A strong electric voltage, supplied by capacitors, is applied across the two electrodes, which produces an electric arc, accompanied by a « pressure wave » that fractures the rock as it propagates through it. Source: according to www.senat.fr/rap/r12-640/r12-64020.html. The aim of this exercise is to study the charging and discharging of capacitors based on data from an experiment carried out at the University of Pau and the Pays de l’Adour. Figure 1: Shale gas and conventional gas production (source: choisir.com). The cross-sectional diagram of the subsoil shows, on the left, a conventional gas well reaching a reservoir pocket located below an aquifer. On the right, a shale gas well descends vertically and then becomes horizontal in a deep layer of shale rich in gas; fractures are shown along the horizontal part. The aquifer is located in an upper layer, above the pockets and the shale rich in gas. Data: - The energy stored by a capacitor can be calculated using the relation $W = \frac{1}{2}\times C\times u_C^2$ with $W$: energy stored by the capacitor in joules (J); $C$: capacitance of the capacitor in farads (F); $u_C$: voltage across the capacitor in volts (V). - The energy efficiency $\eta$, in %, can be calculated using the relation $\eta = \frac{E_{utile}}{E_{consommée}}$. The electrical installation used to power the electrodes can be simplified by an electrical diagram containing (figure 2): - a two-position switch K; - an electrical supply of voltage $E = 40\ \mathrm{kV}$; - an installation allowing 1 to 6 capacitors connected in parallel, each with capacitance $C = 200\ \mathrm{nF}$, represented by an equivalent capacitor of capacitance $C_{eq}$; - an ohmic conductor of resistance $R_1 = 160\ \mathrm{k\Omega}$; - the system {electrodes + water}, which can be modeled by an ohmic conductor of resistance $R_2 = 100\ \Omega$. Figure 2: simplified electrical diagram of the electro-fracturing installation. On the left, a generator $G$ of voltage $E$ is in series with resistance $R_1$; the voltage $u_{R_1}$ is oriented to the right across $R_1$. In the center, an equivalent capacitor $C_{eq}$ is connected vertically between the lower conductor and the moving contact of switch $K$; the voltage $u_{C,eq}$ is oriented upward. The switch $K$ can connect the upper terminal of the capacitor either to position 1, connected to the charging circuit with the generator and $R_1$, or to position 2, connected to the discharge circuit on the right. On the right, resistance $R_2$ is connected vertically; the voltage $u_{R_2}$ is oriented downward. PART A: Charging of the equivalent capacitor In this part, we will study the charging of the equivalent capacitor of capacitance $C_{eq}$ in order to determine the maximum stored energy $W_{max}$. The equivalent capacitor is initially uncharged and switch K is closed in position 1 at time $t = 0\ \mathrm{s}$. A.1. Establish the expression relating the voltage across the equivalent capacitor $u_{C,eq}$, the voltage across the ohmic conductor $u_{R_1}$, and the supply voltage $E$. A.2. Establish the differential equation governing the evolution of the voltage $u_{C,eq}$ across the equivalent capacitor during charging. A.3. Verify that the solution of this differential equation can be written: $u_{C,eq}(t) = E\times\left(1 - e^{-\frac{t}{\tau_{charge}}}\right)$ and express $\tau_{charge}$ in terms of $R_1$ and $C_{eq}$. A.4. Determine the capacitance $C_{eq}$ of the equivalent capacitor. The reasoning will be explained in detail and part of the method will be clearly shown on graph 1 of the appendix to be handed in with the paper (page 10/10). A.5. Deduce the number of capacitors of capacitance $C = 200\ \mathrm{nF}$ used in the experiment. A.6. Determine the maximum energy $W_{max}$ stored in the charged equivalent capacitor. Appendix for exercise III, charging of the equivalent capacitor: Graph 1 "Evolution of the voltage across the equivalent capacitor (charging)". The graph gives the voltage across the capacitor, in volts, as a function of time, in seconds. The horizontal axis goes from $0$ to $0{,}80\ \mathrm{s}$, with major marks at $0{,}20$, $0{,}40$, $0{,}60$ and $0{,}80\ \mathrm{s}$. The vertical axis goes from $0$ to $40000\ \mathrm{V}$, with major marks at $10000$, $20000$, $30000$ and $40000\ \mathrm{V}$. The red experimental points form a rising exponential charge curve: $u_{C,eq}=0\ \mathrm{V}$ at $t=0$, about $25000\ \mathrm{V}$ around $0{,}10\ \mathrm{s}$, about $35000\ \mathrm{V}$ around $0{,}20\ \mathrm{s}$, about $38500\ \mathrm{V}$ around $0{,}35\ \mathrm{s}$, then the curve tends toward a plateau close to $40000\ \mathrm{V}$ from about $0{,}50\ \mathrm{s}$ up to $0{,}80\ \mathrm{s}$. The value corresponding to about 63% of the plateau, that is $0{,}63E \approx 25200\ \mathrm{V}$, is reached at about $t \approx 0{,}10\ \mathrm{s}$. PART B: Discharging of the equivalent capacitor Before the appearance of an electric arc between the two electrodes, the equivalent capacitor is initially charged with a voltage $E = 40\ \mathrm{kV}$, then it undergoes a pre-discharge for a duration $\Delta t = 12\ \mathrm{\mu s}$. For the rest of the exercise, assume that $C_{eq} = 600\ \mathrm{nF}$. During this pre-discharge, the voltage across the equivalent capacitor evolves according to the expression $u_{C,eq}(t) = E\times e^{-\frac{t}{R_2 C_{eq}}}$. At $t = 0\ \mathrm{s}$, switch K is closed in position 2. B.1. Determine the value of the voltage $u_{C,eq}(t = \Delta t)$ across the equivalent capacitor at the end of the pre-discharge. B.2. Deduce the value of the remaining energy $W_{arc}$ in the equivalent capacitor and available for the creation of the electric arc. B.3. Calculate the energy efficiency $\eta$ of the system studied that allows the creation of the electric arc. Comment.
⏳ Solution not generated yet

Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.

📝 See the solution

Have a similar exercise? Get it solved step by step, for free.

🧮 Solve my exercise