Baccalauréat 2025 — Physics-Chemistry specialty, Centres étrangers G1 — exercise 2 : Educational radar equipped with a solar panel (official exam paper)
Statement
The educational radar is a device installed at the roadside to inform the user:
- of the speed at which they are driving,
- of an alert message if their speed is higher than the speed limit.
An educational radar (figure 1) is made up of several elements:
- a rigid mounting support;
- a housing containing a display screen;
- a sensor used to detect moving vehicles;
- a photovoltaic solar panel.
Figure 1. Set of elements that make up an educational radar: drawing showing a solar panel at the top, a housing for the display with an integrated sensor indicating a speed (example 56) and “Danger,” and a vertical mounting support.
Data:
- Photovoltaic solar panel:
• dimensions: 850 mm × 950 mm;
• received luminous power: $P_{\mathrm{lum}} = E \times S$ with $E$ the irradiance in W·m$^{-2}$ and $S$ the panel area in m$^2$;
• stated efficiency: 20 %;
- Average irradiance in the town where the radar is installed: $E = 600$ W·m$^{-2}$.
First, this exercise focuses on the photovoltaic solar panel that supplies electrical power to the educational radar; then, in a second part, on how the radar measures the speed of a vehicle.
1. Electrical supply of the radar: the photovoltaic solar panel
Together with a battery, the radar is electrically powered by means of a photovoltaic solar panel.
To verify the panel efficiency, the following electrical setup is used:
Figure 2. Electrical diagram: a photovoltaic solar panel receives an incident luminous flux; it is connected in a circuit with an ammeter in series measuring the current intensity $I$, a variable resistor $R$, and a voltmeter in parallel across the panel measuring the voltage $U$.
The current intensity $I$ and the electrical voltage $U$ across the panel are measured. The graphs in figure 3 show, for different irradiances, the variation of the current intensity $I$ and the electrical power $P$ supplied by the panel as a function of the voltage $U$ across the panel:
Figure 3. Characteristics of the photovoltaic panel. Graph with horizontal axis “Voltage $U$ (V)” from 0 to 35 V; left vertical axis “Current intensity $I$ (A)” from 0 to 10 A; right vertical axis “Power $P$ (W)” from 0 to 200 W. Blue dashed curves: intensity as a function of voltage for irradiances 200, 400, 600, 800 and 1000 W·m$^{-2}$; the intensity is approximately constant and then drops around 28 to 30 V. For 600 W·m$^{-2}$, the intensity is about 5 A at low voltage and drops near 30 V. Red curves: power as a function of voltage for the same irradiances; for 600 W·m$^{-2}$, the maximum power read is about $P_m = 100$ W near $U \approx 22$ V; for 1000 W·m$^{-2}$, the maximum is close to 200 W.
Q.1. Using figure 3, justify the fact that under the radar’s irradiance conditions, the maximum electrical power delivered is $P_m = 100$ W.
Q.2. Calculate the efficiency $\eta$ of the photovoltaic panel. Conclude.
2. Operation of the radar
A radar sensor consists of a transmitter and a receiving antenna.
The transmitter emits very short electromagnetic signals in the microwave range at frequency $f_E$.
Figure 4. Principle diagram of the operation of a radar: an incident wave is emitted toward a moving car with velocity $\vec v$; the car reflects the wave, which returns as a reflected wave toward the radar.
Vehicles located in the transmitter’s field reflect the received signals, which are then captured by the antenna. The antenna determines the frequency $f_R$ of the received signal.
Q.3. Describe the Doppler effect qualitatively.
In an experimental study that can be carried out in class, the radar sensor is modeled by a transmitter E and a receiver R of ultrasonic waves, fixed and placed side by side on a bench. A plate modeling the moving vehicle is attached to a mobile cart.
Figure 5. Experimental setup: photograph and diagram showing a horizontal bench with a mobile cart carrying a reflective plate; at one end of the bench, a transmitter E and a receiver R of ultrasonic waves are placed side by side. On the diagram, the $x$ axis is horizontal along the bench, the $y$ axis is vertical, the origin $O$ is on the left, and the transmitter-receiver is on the right.
The mobile cart moves horizontally along the bench, in the Earth frame assumed to be Galilean.
Data:
- Air temperature inside the room: $\theta = 21,0\ ^\circ$C;
- In the whole exercise:
• the friction forces exerted by the air and the bench on the cart are neglected;
• the cart speed $v_{\mathrm{chariot}}$ is assumed constant.
- Speed of propagation $v$ of sound waves in air as a function of temperature: table with $\theta$ (°C) = 15,0 ; 16,0 ; 17,0 ; 18,0 ; 19,0 ; 20,0 ; 21,0 ; 22,0 and $v$ (m·s$^{-1}$) = 340,61 ; 341,21 ; 341,82 ; 342,43 ; 343,03 ; 343,64 ; 344,25 ; 344,85.
- Expression of the Doppler shift for the radar sensor: $\Delta f = 2 \times f_E \times \dfrac{v_{\mathrm{chariot}}}{v}$ with $f_E$ and $\Delta f$ in Hz, $v_{\mathrm{chariot}}$ and $v$ in m·s$^{-1}$.
Measurement of the cart speed using tracking
Tracking a point on the cart at regular time intervals, marked by the “+” (figure 6), is carried out to obtain the cart trajectory (figure 7).
Figure 6. Cart: photograph of the cart on the bench, with a “+” marker attached to the cart used for tracking.
Figure 7. Excerpt from the recording obtained between the dates $t_0 = 0$ s and $t_{13} = 0,429$ s. Graph $y$ (mm) as a function of $x$ (mm): the points $M_0$ to $M_{13}$ are almost horizontally aligned near $y=0$; the $x$ axis is scaled from 0 to a little more than 40 mm. The positions are approximately regularly spaced, from $M_0$ near $x=0$ mm to $M_{13}$ near $x\approx 42$ mm.
Q.4. Calculate the values of the speeds $v_7$ and $v_{11}$ of the cart respectively at times $t_7$ and $t_{11}$.
The processing of the acquired data makes it possible to plot the time variation of two quantities; the position $x$ (in m) and the horizontal speed $v_x$ (in m·s$^{-1}$) of the cart: $x = f(t)$ and $v_x = g(t)$ (figures 8a and 8b).
Figure 8a. Curve A: graph as a function of time $t$ (s), from 0 to about 0,43 s; the ordinate is almost constant around 0,09 to 0,10, with points scattered between about 0,088 and 0,100.
Figure 8b. Curve B: graph as a function of time $t$ (s), from 0 to about 0,43 s; the ordinate increases linearly from 0 to about 0,041, with aligned points (for example about 0,01 at $t=0,10$ s, 0,02 at $t=0,21$ s, 0,03 at $t=0,32$ s, 0,04 at $t=0,42$ s).
Q.5. Associate, with justification, each curve A and B in figures 8a and 8b with the corresponding quantity.
Q.6. Estimate, from one of figures 8a or 8b, the value of the average speed of the cart.
Measurement of the cart speed using the Doppler effect
The signal received by the ultrasonic-wave receiver when the cart remains stationary is recorded. The resulting curve of the voltage across the receiver as a function of time is shown below (figure 9).
Figure 9. Recording of the received signal (the cart being stationary): graph of $U_{\mathrm{récepteur}}$ (V) as a function of time $t$ (µs), from 0 to about 145 µs. Sinusoidal signal with amplitude about 0,22 V; successive maxima are spaced by about 24 µs, which corresponds to a frequency close to 42 kHz.
Q.7. Determine the value of the period $T_R$ of the obtained signal. Deduce that the value of the frequency $f_E$ of the signal emitted by the transmitter is 42 kHz.
A new acquisition of the emitted signal and the received signal is carried out when the cart is moving, as it approaches the transmitter and the receiver. The measured Doppler shift is $\Delta f = 22,7$ Hz.
Q.8. Calculate the value of $v_{\mathrm{chariot}}$, the cart speed obtained by the Doppler effect. Compare the result obtained with those from questions Q.4 and Q.6.
⏳ Solution not generated yet
Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.
📝 See the solutionHave a similar exercise? Get it solved step by step, for free.
🧮 Solve my exercise