Solved exercises🧮 Solve my exercise

Baccalauréat 2025 — Physics-Chemistry specialty, Asie (jour 1) — exercise 1 : Sanitary installation (official exam paper)

PhysicsLevel : High schoolSanitary installation🌐 Lire en français
Statement
To reduce their consumption of fossil fuels and lower their bills, a newly acquired couple wants to invest in an installation using solar energy to heat the water in their home. To do this, a complete reorganization of the house’s sanitary installation is necessary. In the first part of this exercise, we study the thermal transfers that make it possible to heat water using solar thermal panels. Then we consider the possibility of installing a booster pump to ensure proper distribution of hot water. Part 1 – Heating water To limit electrical energy consumption, the new owners have installed a solar thermal panel connected to a hot-water tank. Figure 1 below shows a diagram of the complete system. Figure 1: Diagram of the system. The diagram shows a solar panel placed on a roof, illuminated by the Sun. A cold heat-transfer fluid rises to the solar panel, is heated there, then flows back down as a hot heat-transfer fluid toward a coil located in a hot-water tank. In the tank, cold water enters at the bottom and hot water exits at the top. The tank contains a thermometer. According to https://www.otovo.fr/blog/le-solaire-et-vous/chauffe-eau-solaire Q1- Identify the mode of thermal transfer involved: a) at the solar thermal panel. b) between the hot heat-transfer fluid and the domestic hot water in the tank. c) in the tank between the hot water at the bottom and the cold water at the top. To limit thermal losses, the solar panel contains an insulating layer placed between the heat-transfer fluid, heated by the Sun, and the lower structure of the panel (Figure 2). This insulating layer is made either of melamine resin or rigid polyurethane foam. Figure 2: Diagram of the structure of the solar panel. The diagram shows, from top to bottom, a layer containing the heat-transfer fluid, a layer of insulation, and then the lower structure of the solar panel. Data: - Thermal conductivities $\lambda$ of materials, in $\mathrm{W\cdot m^{-1}\cdot K^{-1}}$: melamine resin: 0.033; rigid polyurethane foam: 0.025. - The thermal resistance of the insulator is given by $R_{th}=\dfrac{e}{\lambda\times S}$ where $e$ is the thickness of the insulator in m, $S$ is its area in $\mathrm{m^2}$ and $\lambda$ is its thermal conductivity in $\mathrm{W\cdot m^{-1}\cdot K^{-1}}$. - The thermal flux through the insulator is given by $\Phi=\dfrac{\Delta \theta}{R_{th}}$ where $\Delta \theta$ is the temperature difference between the upper and lower parts of the insulator (Figure 2). Q2- Calculate the thermal resistance $R_{th}$ of a melamine resin insulator of thickness $e = 5{,}0\ \mathrm{cm}$ for a solar panel of area $S = 5{,}0\ \mathrm{m^2}$. Q3- Knowing that the lower structure of the panel has a temperature $\theta_p = 20\ ^\circ\mathrm{C}$ and that the heat-transfer fluid has a temperature $\theta_c = 45\ ^\circ\mathrm{C}$, determine the value of the thermal flux $\Phi$ passing through the melamine resin insulator. Q4- Indicate, with justification, the direction of heat transfer between the lower structure of the panel and the heat-transfer fluid. Q5- Compare, with justification and without calculation, the value of the thermal flux calculated previously and that of the thermal flux that would pass through the same device for a rigid polyurethane foam insulator. Comment on the choice of insulator. The tank of volume $V = 150\ \mathrm{L}$ is the site of a thermal transfer $Q$ that makes it possible to heat the stored water. The water in the tank is considered to be a motionless, incompressible system that is perfectly thermally insulated. Data: - Specific heat capacity of water: $c_{eau}=4\ 180\ \mathrm{J\cdot kg^{-1}\cdot ^\circ C^{-1}}$ - Mass density of water: $\rho_{eau}=1{,}00\ \mathrm{kg\cdot L^{-1}}$ - Relation between thermal power $P_{th}$ (in W), heat transfer $Q$ (in J) and duration of the heat transfer $\Delta t$ (in s): $Q=P_{th}\times \Delta t$ - Expression for the efficiency $r$ of a converter: $r=\dfrac{P_{utile}}{P_{reçue}}$ Q6- Give the expression for the change in internal energy $\Delta U$ of the water contained in the tank as a function of the specific heat capacity $c_{eau}$, the volume $V$, the density $\rho_{eau}$, and the initial and final temperatures $\theta_i$ and $\theta_f$ of the water. Q7- Deduce the expression for the heat transfer $Q$ by applying the first law of thermodynamics. The solar thermal panel of area $S = 5{,}0\ \mathrm{m^2}$ receives a surface radiative power $p_R = 600\ \mathrm{W\cdot m^{-2}}$. The efficiency of the installed solar water heater is 77 %. Q8- Calculate the thermal power $P_{th}$ supplied by the solar water heater. Q9- Determine the duration $\Delta t$, in hours, required for the water in the tank to go from an initial temperature $\theta_i = 10\ ^\circ\mathrm{C}$ to a final temperature $\theta_f = 50\ ^\circ\mathrm{C}$. Comment. To answer this question, the candidate is invited to take initiatives and present the method followed, even if it did not lead to a result. The method is assessed and must be clearly presented. Part 2 – Booster pump To obtain comfortable water pressure at the taps located upstairs, it is sometimes advisable to use a booster pump. This device is installed at the inlet of the system if the water pressure supplied is less than 2.0 bar. Data: - Acceleration due to gravity: $g=9{,}81\ \mathrm{m\cdot s^{-2}}$ - Mass density of water: $\rho_{eau}=1{,}00\times 10^3\ \mathrm{kg\cdot m^{-3}}$ - Conversion: $1{,}0\ \mathrm{bar}=1{,}0\times 10^5\ \mathrm{Pa}$ - Expression for volumetric flow rate: $D=v\times S$ where $v$ is the flow speed of the water (in $\mathrm{m\cdot s^{-1}}$) and $S$ is the cross-sectional area of the pipe (in $\mathrm{m^2}$). - Bernoulli’s relation may be applied along a streamline of an incompressible fluid in steady flow independent of time. It is written: $\dfrac{1}{2}\rho_{eau}\,v^2+\rho_{eau}\,g\,z+P=\mathrm{constante}$. The following table defines $z$ and $P$ and gives the characteristics of the dwelling. Table: characteristics of the sanitary installation of the dwelling. Columns: Tank inlet; Upstairs tap. Altitude $z$ (in m): 0.0; 5.0. Cross-sectional area $S$ (in $\mathrm{m^2}$): $2{,}0\times 10^{-4}$; $1{,}1\times 10^{-4}$. Pressure $P$ (in Pa): $3{,}0\times 10^5$; $P_2$. Flow speed $v$ (in $\mathrm{m\cdot s^{-1}}$): 1.0; $v_2$. The water is considered to be an incompressible fluid in steady flow independent of time. Q10- Indicate, with justification, the relation between the volumetric flow rates $D_1$ at the tank inlet and $D_2$ at the upstairs tap. Q11- Deduce that the water speed at the upstairs tap has the value $v_2 = 1{,}8\ \mathrm{m\cdot s^{-1}}$. Q12- Determine the value of the water pressure $P_2$ at the outlet of the upstairs tap by applying Bernoulli’s relation. Q13- Indicate whether a booster pump is necessary at the inlet of the sanitary installation of the home newly purchased by the couple.
⏳ Solution not generated yet

Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.

📝 See the solution

Have a similar exercise? Get it solved step by step, for free.

🧮 Solve my exercise