Baccalauréat 2025 — Physics-Chemistry specialty, Métropole — exercise 1 : Measurement of the Thickness of Cling Film (official exam paper)
Statement
Stretch cling films are flexible, transparent plastic films used mainly to preserve food. They are made from polymers such as low-density polyethylene (LDPE) and sometimes polyvinyl chloride (PVC). These films provide a barrier against air, moisture and contaminants, thus helping to extend food freshness and reduce food waste. The thickness of the film is an essential parameter for the mechanical properties (elasticity, tensile strength) of stretch films, as well as for their environmental impact.
The aim of this exercise is to study different methods for determining the thickness of a food film.
1. Measuring the thickness of a food film by capacitance
Data:
- a parallel-plate capacitor is made up of two metallic plates parallel to each other, each of surface area $S$, separated by an insulating material (paper, plastic) of thickness $e$;
- literal expression of the capacitance $C$ of such a capacitor: $C=\dfrac{\varepsilon_0\cdot \varepsilon_r\cdot S}{e}$ with: $\varepsilon_0=8,85\times10^{-12}\ \mathrm{F\cdot m^{-1}}$ : permittivity of free space; $\varepsilon_r$ : relative permittivity of the insulating material;
- relative permittivity of the food film studied: $\varepsilon_{r,\mathrm{film}}=2,3$;
- relative permittivity of air: $\varepsilon_{r,\mathrm{air}}=1,0$;
- reference thickness of the food film: $e_{\mathrm{film,ref}}=7,6\ \mu\mathrm{m}$;
- to discuss whether the result of a measurement agrees with a reference value, one may use the quotient $\dfrac{|x-x_{\mathrm{ref}}|}{u(x)}$ with $x$ the measured value, $x_{\mathrm{ref}}$ the reference value and $u(x)$ the standard uncertainty associated with the measured value $x$.
A parallel-plate capacitor is made by placing a single layer of transparent film of thickness $e$ between two rectangular sheets of aluminium foil, with dimensions $21\ \mathrm{cm}\times 28\ \mathrm{cm}$. Its capacitance is denoted by $C$. Figure 1: cross-sectional view of the parallel-plate capacitor; two parallel aluminium plates frame a layer of food film, the total thickness between the plates is denoted by $e$.
The circuit is then assembled with the capacitor made, an ohmic conductor of resistance $R=1,00\ \mathrm{k}\Omega$, a switch and an ideal generator delivering a direct voltage $E=4,9\ \mathrm{V}$. Figure 2: circuit diagram; ideal voltage source $E$, switch, resistor $R$ and capacitor $C$ in series; the voltage across the capacitor is denoted by $u_C$.
The charging of the capacitor is studied from $t=0$, the instant when the switch is closed. The time evolution of the voltage $u_C$ across the capacitor is shown in figure 3. Figure 3: graph of $u_C$ as a function of time $t$; horizontal axis $t$ in $\mu\mathrm{s}$ from 0 to 400; vertical axis $u_C$ in V from 0 to 5,5. The curve rises exponentially from $u_C=0$ at $t=0$ toward a limiting value close to $4,9\ \mathrm{V}$; approximate readings: $u_C\approx2,5\ \mathrm{V}$ at $50\ \mu\mathrm{s}$, $u_C\approx3,8\ \mathrm{V}$ at $100\ \mu\mathrm{s}$, $u_C\approx4,4\ \mathrm{V}$ at $150\ \mu\mathrm{s}$, $u_C\approx4,65\ \mathrm{V}$ at $200\ \mu\mathrm{s}$, $u_C\approx4,8\ \mathrm{V}$ at $300\ \mu\mathrm{s}$ and $u_C\approx4,85\ \mathrm{V}$ at $400\ \mu\mathrm{s}$.
Q1. Establish the differential equation below satisfied by the voltage $u_C$ across the capacitor, where $\tau$ is the characteristic time whose expression you will give: $\dfrac{\mathrm{d}u_C}{\mathrm{d}t}+\dfrac{1}{\tau}u_C=\dfrac{E}{\tau}$.
The solution of this differential equation is: $u_C(t)=A\left(1-e^{-\frac{t}{\tau}}\right)$ where $A$ is a constant.
Q2. Determine the expression for the constant $A$.
Q3. Express, in terms of $E$, the voltage $u_C(\tau)$ across the capacitor at time $t=\tau$.
Q4. Use the curve in figure 3 and the result obtained in question Q3 to determine the value of the time constant $\tau$ of the circuit. Explain the method used.
Q5. Deduce an experimental value for the capacitance $C$ of the capacitor.
Additional repeated measurements made it possible to determine an average value of the capacitance of the capacitor: $C=69,8\ \mathrm{nF}$.
Q6. Determine the value of the thickness $e_{\mathrm{film}}$ of the food film deduced from this average value.
With this method, the standard uncertainty on the film thickness is: $u(e_{\mathrm{film}})=1,0\ \mu\mathrm{m}$.
Q7. Discuss whether the result obtained in question Q6 agrees with the reference thickness of the film given in the data.
To explain the observed difference, one may assume that there is between the aluminium sheets, in addition to the thickness of the food film, a thin layer of air of constant thickness $e_{\mathrm{air}}$. The situation is then schematized in figure 4. Figure 4: trapped air layer in the capacitor; between two aluminium plates, a layer of food film of thickness $e_{\mathrm{film}}$ and a layer of air of thickness $e_{\mathrm{air}}$ are superposed.
It can be shown that the capacitance $C’$ of a capacitor, in the case where the capacitor includes an air thickness $e_{\mathrm{air}}$ and a film thickness $e_{\mathrm{film}}$, is given by the relation: $C'=\dfrac{\varepsilon_0\cdot S}{\dfrac{e_{\mathrm{air}}}{\varepsilon_{r,\mathrm{air}}}+\dfrac{e_{\mathrm{film}}}{\varepsilon_{r,\mathrm{film}}}}$.
Q8. Considering two limiting cases of the diagram shown in figure 4, verify that the expression given above is compatible with the literal expression for the capacitance of a capacitor specified in the data.
Q9. In this model, determine the value of the air thickness $e_{\mathrm{air}}$ assuming that the thickness of the food film is the reference value: $e_{\mathrm{film,ref}}=7,6\ \mu\mathrm{m}$. Comment.
2. Measuring the thickness of the food film by weighing
Data:
- dimensions of the food film indicated on the packaging: width $\ell=29\ \mathrm{cm}$ and length $L=30\ \mathrm{m}$;
- density of the polymer making up the food film: $\rho_{\mathrm{film}}=1,25\times10^3\ \mathrm{kg\cdot m^{-3}}$.
In order to estimate the order of magnitude of the thickness of the food film, the mass of film on a new roll is measured: $m_{\mathrm{film}}=70,56\ \mathrm{g}$.
Q10. Calculate the thickness $e_{\mathrm{film}}$ of the food film in the roll.
3. Measuring the thickness of the food film by interferometry
In order to obtain a more accurate measurement of the thickness of the food film, an interferometric method is used in which the film is illuminated with a light source as shown in figure 5.
In this study, only two light rays ① and ② originating from the same incident ray are considered, as shown in figure 5:
- ray ①: ray originating from the incident ray that is reflected at the upper surface of the food film;
- ray ②: ray originating from the incident ray that is transmitted into the film then reflected by the lower surface of the film and that exits through the upper surface of the film.
Rays ① and ② are parallel to each other. Using a lens, they are superimposed at the entrance of an optical fiber, itself connected to a spectrometer. Figure 5: experimental setup; a light source emits an incident ray toward a sheet of food film of thickness $e_{\mathrm{film}}$. Ray ① is reflected at the upper surface; ray ② enters the film, is reflected at the lower surface, then exits. A converging lens gathers the two rays toward an optical fiber connected to a spectrometer.
For a monochromatic source of wavelength $\lambda$, the superposition of the two waves associated with rays ① and ② gives rise to interference. Let $\delta$ be the optical path difference between the two waves.
Q11. State the relation between $\delta$ and $\lambda$ allowing constructive interference to be obtained.
The interference order $p$ is, in the general case, defined as the ratio $p=\dfrac{\delta}{\lambda}$. It is assumed that, under the experimental conditions, the interference order $p$ is given by the following relation: $p=\dfrac{\beta\times e_{\mathrm{film}}}{\lambda}+\dfrac{1}{2}$, relation 1, where $\beta$ is a dimensionless parameter depending on the refractive index of the film and the angle of incidence of the light on the film.
Q12. State, with justification and without calculation, the phenomenon observed when the ratio $\dfrac{\beta\times e_{\mathrm{film}}}{\lambda}$ is an integer.
In the experiment studied, the film is illuminated with white light and the spectrum of the light carried by the fiber is analyzed. Figure 6a below shows the spectrum of the incident light and figure 6b that of the light collected by the optical fiber. Figure 6a: spectrum of the incident light; horizontal axis wavelength from 400 to 900 nm, vertical axis intensity in arbitrary units. The intensity forms a broad band increasing from 400 nm to a maximum around 680–700 nm then decreasing toward 900 nm, with a narrow dip around 705 nm and a small irregularity around 560–580 nm. Figure 6b: spectrum of the light collected by the fiber; same spectral range, broad similar envelope but modulated by interference maxima and minima between about 580 and 730 nm; several maxima are circled with dashed lines around approximately 630 nm, 650 nm, 670 nm and 690 nm.
Q13. The spectrum in figure 6b shows intensity maxima, some of which are circled with dashed lines. Explain their origin.
Analysis of figure 6b makes it possible to represent the variation of the interference order as a function of the inverse of the wavelength. The results obtained and their modelling are shown in figure 7. Figure 7: graph of the interference order $p$ as a function of $\dfrac{1}{\lambda}$; horizontal axis $\dfrac{1}{\lambda}$ in $\mathrm{nm^{-1}}$ from 0,00135 to 0,00165; vertical axis $p$ from 31 to 38. The experimental points are approximately aligned: $(0,00140;32)$, $(0,00145;33)$, $(0,00149;34)$, $(0,00153;35)$, $(0,00158;36)$, $(0,00163;37)$. The indicated modelling line is $p=22443\times\dfrac{1}{\lambda}+0,51$ with $\lambda$ in nm.
Q14. Indicate, with justification, whether the experimental results are consistent with relation 1.
Q15. Deduce from these measurements the value of the thickness $e_{\mathrm{film}}$ of the food film, knowing that, under the experimental conditions, $\beta=3,02$. Comment.
⏳ Solution not generated yet
Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.
📝 See the solutionHave a similar exercise? Get it solved step by step, for free.
🧮 Solve my exercise