Solved exercises🧮 Solve my exercise

Baccalauréat 2025 — Physics-Chemistry specialty, Métropole remplacement — exercise 1 : Physics at the service of the winemaker (official exam paper)

PhysicsLevel : High schoolPhysics at the service of the winemaker🌐 Lire en français
Statement
Winemaking is the process of transforming grape juice into wine by fermentation. During the first stages of winemaking, the grape berries are crushed and the extracted juice is placed in a storage tank. Alcoholic fermentation then begins, a stage during which part of the sugar is transformed into alcohol. During this process, the winemaker must control the temperature and the density of the juice. The aim of this exercise is to study how physics can be useful to the winemaker to measure the filling level of the storage tank, control the temperature of the grape juice and determine its sugar content during fermentation. 1. Study of the operating principle of the level sensor The storage tank is equipped with a capacitive level sensor used to control the height of the liquid (figure 1). Figure 1. Diagram of a storage tank with level sensor: a storage tank contains a liquid of height $h$; a vertical rod, the level sensor, dips into the tank along a wall. This sensor consists of a conductive rod coated with a very thin insulating layer. When it is immersed in a conductive liquid, such as grape juice, it forms one plate of a capacitor and the liquid forms the other. For simplicity, the whole system is considered to behave like a parallel-plate capacitor (figure 2). The operating principle of this sensor and the influence of the liquid height on the behaviour of such a capacitor are studied in the laboratory by making the setup shown in figure 3: - a rectangular aluminium sheet of width $\ell = 41\ \text{cm}$ forms plate 1 of the capacitor; - a plastic-coated sheet of thickness $e = 80\ \mu\text{m}$ of polyester acts as the insulator; - the plate, formed by the aluminium sheet and the plastic-coated sheet, is immersed in a container and touches the bottom. It is in contact over a height $h$ with a conductive liquid that plays the role of plate 2 of the capacitor; - a bare wire makes electrical contact with the liquid. Figure 2. Geometrical characteristics of a parallel-plate capacitor: two parallel plates separated by an insulator of thickness $e$; the facing area has height $h$ and width $\ell$. Figure 3. Diagram of the experimental setup: a vertical aluminium sheet of width $\ell$ (plate 1), covered with an insulator of thickness $e$, dips into a conductive liquid (plate 2) over a height $h$; above the liquid is air; a bare wire dips into the liquid; the bottom of the beaker is indicated. Given: - the area $S_C$ of each plate in the experimental setup is expressed by the relation: $S_C = h\cdot \ell$; - the capacitance $C$ of the parallel-plate capacitor in this setup is expressed by the relation: $C = \dfrac{\varepsilon\,S_C}{e}$ with $C$ in farad (F), $S_C$ in $\text{m}^2$, $e$ in m and $\varepsilon$, a characteristic quantity of the insulator called permittivity, expressed in $\text{F}\cdot\text{m}^{-1}$. Q1. Explain why this sensor cannot be used in an insulating liquid. Q2. State whether the capacitance $C$ of the capacitor increases or decreases when the height $h$ of the liquid in which the system is immersed increases. To measure the value of the capacitor’s capacitance, the electrical circuit shown in figure 4 is set up. It includes: - an ideal voltage generator $E = 5{,}0\ \text{V}$; - an ohmic conductor of resistance $R = 6{,}0\times10^6\ \Omega$; - the experimental setup of figure 3 acting as a capacitor of capacitance $C$; - a two-position switch. Figure 4. Diagram of the electrical circuit used to measure the capacitance $C$: an ideal voltage generator $E$ is connected, via a two-position switch, to a resistor $R$ in series with a capacitor $C$. In position 1, the capacitor is discharged. At time $t=0$, the switch changes to position 2 to charge the capacitor. The current $i(t)$ flows toward the resistor; the voltages $u_R(t)$ and $u_C(t)$ are indicated across the resistor and the capacitor. The switch is first placed in position 1 in order to discharge the capacitor. At time $t = 0$, the capacitor is discharged and the switch is changed to position 2. Q3. Show that, during its charging, the voltage $u_C(t)$ across the capacitor satisfies the following differential equation: $\dfrac{du_C}{dt}+\dfrac{u_C}{R\cdot C}=\dfrac{E}{R\cdot C}$. Q4. The voltage expression $u_C(t)=A\cdot e^{-\frac{t}{\tau}}+B$ is a solution of this differential equation. Determine, as a function of the parameters $E$, $R$ and $C$, the expressions of the constants $A$, $B$ and $\tau$ suitable for the experimental conditions. A first charging experiment is carried out for a liquid height $h_{\text{test}}$. Figure 5 shows the time evolution of the voltage $u_C(t)$ across this capacitor. Figure 5. Time evolution of the voltage $u_C(t)$ across the capacitor during charging: graph with $u_C$ in V on the vertical axis from 0 to 5 V and $t$ in s on the horizontal axis from 0 to 0,7 s. The experimental points form a rising charging curve starting from 0 V at $t=0$, passing approximately through $(0{,}05\ \text{s}; 2{,}2\ \text{V})$, $(0{,}10\ \text{s}; 3{,}2\ \text{V})$, $(0{,}15\ \text{s}; 3{,}9\ \text{V})$, $(0{,}20\ \text{s}; 4{,}3\ \text{V})$, $(0{,}30\ \text{s}; 4{,}75\ \text{V})$, then tending toward the asymptote $5{,}0\ \text{V}$ from 0,5 to 0,7 s. The experiment is repeated for different liquid heights $h$. The graph of the variation of the capacitor’s capacitance as a function of the liquid height is given in figure 6. A model line has been drawn. Figure 6. Variation of the capacitance $C$ of the capacitor as a function of the liquid height $h$: graph with $C$ in nF on the vertical axis from 0 to 34 nF and $h$ in cm on the horizontal axis from 0 to 24 cm. The experimental points are aligned on a straight line passing near the origin; approximate read values: $(3\ \text{cm}; 5{,}3\ \text{nF})$, $(5\ \text{cm}; 8{,}2\ \text{nF})$, $(8\ \text{cm}; 12{,}7\ \text{nF})$, $(10\ \text{cm}; 15{,}4\ \text{nF})$, $(13\ \text{cm}; 19{,}6\ \text{nF})$, $(15\ \text{cm}; 22{,}2\ \text{nF})$, $(18\ \text{cm}; 26{,}1\ \text{nF})$, $(20\ \text{cm}; 29{,}0\ \text{nF})$, $(23\ \text{cm}; 33{,}1\ \text{nF})$. The model line has a slope of about $1{,}4\ \text{nF}\cdot\text{cm}^{-1}$. Q5. Using figures 5 and 6, determine the liquid height $h_{\text{test}}$ used in the first experiment. The candidate is invited to take initiative and present the approach followed, even if it was unsuccessful. The approach is assessed and must be presented correctly. 2. Control of the temperature of the grape juice In order for alcoholic fermentation to occur, the temperature of the juice must be maintained around 18 °C. Thus, the storage tank is equipped with a heat exchanger immersed in the juice making it possible either to heat or to cool the juice, depending on the observed variations in its temperature. The aim is to establish the energy balance of the system {grape juice} in order to determine the power of the heat exchanger to be used. Figure 7 shows the powers exchanged between the system {grape juice} and the external environment. The grape juice is considered to be in thermal equilibrium. Figure 7. Power balance of the system: an oval “Grape juice” receives a thermal flux $\Phi_P$ (in W) through the walls of the storage tank, arrow pointing toward the juice from the left, and a thermal power $P$ (in W) from the heat exchanger, arrow pointing toward the juice from the right. Given: - temperature of the juice to be maintained during alcoholic fermentation: $\theta_{\text{jus}} = 18\ ^\circ\text{C}$; - average outside air temperature: $\theta_{\text{ext}} = 22\ ^\circ\text{C}$; - characteristics of the storage tank: - capacity: $V = 2\ \text{m}^3$; - thermal exchange area: $S = 9\ \text{m}^2$; - the thermal capacity of the whole grape juice is denoted by $C_J$ (in $\text{J}\cdot\text{K}^{-1}$); - fermentation of a mass of juice $m_{\text{jus}}$ releases a power $P_F$ given by an empirical law: $P_F = 0{,}127\cdot m_{\text{jus}}$ where $m_{\text{jus}}$ is in kg and $P_F$ in W; - thermal flux between the outside and the inside of the storage tank: $\Phi_P = A\cdot S\cdot(\theta_{\text{ext}}-\theta_{\text{jus}})$ with: - $S$ the thermal exchange area (in $\text{m}^2$); - $A$ the overall heat transfer coefficient through the walls of the storage tank: $A = 12\ \text{W}\cdot\text{m}^{-2}\cdot\text{K}^{-1}$; - density of the grape juice during alcoholic fermentation: $\rho_{\text{jus}} = 1\ 090\ \text{kg}\cdot\text{m}^{-3}$. Q6. State, with justification, the direction of thermal transfer occurring between the juice maintained at temperature $\theta_{\text{jus}}$ and the outside air at temperature $\theta_{\text{ext}}$ during alcoholic fermentation. Q7. Calculate the value of the global thermal flux $\Phi_P$ through the walls of the storage tank. Q8. Calculate the power $P_F$ released by the fermentation of the grape juice in the completely filled storage tank. It is assumed that, given the energy release linked to fermentation, the first law of thermodynamics applied to the closed system {grape juice}, whose temperature varies by $\Delta\theta$ between two instants $t$ and $t+\Delta t$, leads to the relation below: $C_J\cdot\Delta\theta=(\Phi_P+P+P_F)\cdot\Delta t$. Q9. Determine the value of the thermal power $P$ of the internal heat exchanger placed in the storage tank that makes it possible to keep the juice temperature constant. Interpret the sign of $P$. 3. Control of the sugar content in grape juice and principle of the mustimeter Measuring the sugar content of a grape juice allows the winemaker to monitor the fermentation process over time. When the sugar content has stabilized at its minimum, the alcoholic fermentation stage is complete. To do this, the winemaker uses a mustimeter, an instrument that measures the density $\rho_{\text{jus}}$ of the juice. This measurement then makes it possible to know the mass concentration of sugar. This part studies the operating principle of a mustimeter. Given: - Archimedes’ buoyant force is the force exerted by a fluid on a system immersed in this fluid. Its characteristics are: - direction: vertical; - sense: upward; - value: $\Pi_A=\rho\cdot V\cdot g$ where $\rho$ is the density of the fluid, $V$ is the volume of the immersed part of the system and $g$ is the acceleration due to gravity; - the mustimeter studied, of mass $m_0 = 55\ \text{g}$, is composed of two parts: - a wide tube, completely immersed, of volume $V_0 = 49\ \text{mL}$; - a thin graduated tube, cylindrical in shape, partially immersed, of cross-sectional area $S_T = 5\times10^{-5}\ \text{m}^2$; the immersed height of the tube is denoted by $h_T$; - Archimedes’ buoyant force due to air is neglected compared with that exerted by grape juice. To carry out the measurement, the mustimeter is placed in a sample of grape juice, floats and stabilizes: the density can then be read on the graduated thin tube (see figure 8). Figure 8. Diagram of a mustimeter: a container holds grape juice; the mustimeter floats vertically. Its lower part, a wide tube, is completely immersed; its upper part, a thin graduated tube, is partially immersed. The immersed height of the thin tube is denoted by $h_T$. A second isolated diagram shows the graduated thin tube of the mustimeter and the wide tube of the mustimeter. Q10. Identify the two forces acting on the system {mustimeter} in equilibrium in the grape juice. Q11. Show that the height $h_T$ of the immersed part of the thin tube can be written in the form: $h_T=\dfrac{m_0}{\rho_{\text{jus}}\cdot S_T}-\dfrac{V_0}{S_T}$ with $\rho_{\text{jus}}$: the density of the grape juice. Q12. The graduations on the thin tube of the mustimeter indicate the value of the density of the liquid, expressed in $\text{g}\cdot\text{mL}^{-1}$. Qualitatively justify that the mustimeter sinks deeper when the density of the juice decreases. The measuring range of the mustimeter corresponds to an immersed height $h_T$ varying between 1 cm and 14 cm. Q13. Determine the minimum density $\rho_{\text{jus,min}}$ that this mustimeter can measure. Q14. The density of grape juice decreases as the degree of fermentation increases. Explain the problem encountered when using this mustimeter with a juice that is too fermented.
⏳ Solution not generated yet

Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.

📝 See the solution

Have a similar exercise? Get it solved step by step, for free.

🧮 Solve my exercise