Solved exercises🧮 Solve my exercise

Baccalauréat 2026 — Physics-Chemistry specialty, Centres étrangers G1 (jour 1) — exercise 1 : Study of an electric harp in the service of domestic bees (official exam paper)

PhysicsLevel : High schoolStudy of an electric harp in the service of domestic bees🌐 Lire en français
Statement
For several years, beekeepers have been faced with the invasion of Asian hornets, which attack the bees in their apiaries. To protect themselves, they can place an electric harp (Figure 1) powered by a solar panel near the hive. When the hornet touches two wires of the harp, it is electrocuted and then falls into a water tray placed below the harp. Figure 1 – Electric harp: photograph of an electric harp made up of a rectangular support carrying many vertical parallel stainless-steel wires; a water tray is placed under the wires. On the right side there is a solar panel that powers the harp and an electrical box. This exercise studies the size of the stainless-steel wire present on the harp, the power supply system of the harp and the electrical module used to create the electric discharges that neutralize the Asian hornets. 1. Size of the stainless-steel wire present on the harp The electric harp is made of vertical stainless-steel wires spaced 2,7 cm apart, a width sufficient to let bees pass through, but not Asian hornets. In order not to be seen by the hornets, the wires must have a maximum diameter of the order of 0,5 mm. To check the diameter value of a wire indicated as 0,45 mm on a spool intended to be used to make an electric harp, the device shown in Figure 2 is used. A wire of diameter $a$ is placed in the path of a laser beam of wavelength $\lambda$ and a screen is placed at a distance $D$ from the wire. A series of bright spots appears on the screen. Figure 2 – Diagram of the experimental setup: a laser emits an incident beam toward a vertical wire of diameter $a$. The emerging beam is diffracted and reaches a screen located at distance $D$ from the wire. The central bright spot on the screen has a width $L$. The extreme directions of the central spot make an angle $\theta$ on either side of the axis of the incident beam. The width $L$ of the central bright spot is measured directly on the screen. The ends of this central spot are identified by an angle $\theta$ defined with respect to the direction of the incident beam and that of the emerging beam. Data: For very small angles $\theta$ (expressed in radians): - $\tan \theta = \theta$; - the angle $\theta$ depends on the wavelength $\lambda$ of the laser and on the diameter $a$ of the wire: $\theta = \dfrac{\lambda}{a}$. Q.1. Name the physical phenomenon observed on the screen. Q.2. Express the characteristic angle $\theta$ as a function of the width $L$ of the central spot and the distance $D$, using Figure 2 and the small-angle approximation. Q.3. Deduce the relation giving the width $L$ of the central spot as a function of the wavelength $\lambda$, the diameter $a$ of the wire and the distance $D$ between the wire and the screen. Show that there is proportionality between $L$ and $\dfrac{1}{a}$. To determine precisely the diameter of the wire intended for making the harp, a calibration is carried out using six calibrated wires of known diameter. For each of them, the width $L$ of the central spot observed on the screen is measured. The following measurement table is obtained: Measurement table: $a$ (µm): 40 ; 50 ; 100 ; 120 ; 280 ; 400. $L$ (cm): 9,50 ; 7,40 ; 3,95 ; 3,20 ; 1,35 ; 1,00. The graph $L = f(1/a)$ is plotted. Figure 3 – Graphical representation of $L$ as a function of $1/a$: horizontal axis $1/a$ in $10^3\ \text{m}^{-1}$ from 0 to 25; vertical axis $L$ in $10^{-2}\ \text{m}$ from 0 to about 9. The experimental points shown are approximately: $(2{,}5 ; 0{,}95)$, $(3{,}3 ; 1{,}25)$, $(8{,}3 ; 3{,}1)$, $(10 ; 3{,}85)$, $(20 ; 7{,}35)$ and $(25 ; 9{,}35)$. Q.4. Justify that the experimental results in Figure 3 are consistent with the model $L = k \times \dfrac{1}{a}$ where $k$ is a constant. Q.5. Determine the value of $k$ stating the method used. A model of the measurement series gives $k = 3{,}85 \times 10^{-6}\ \text{m}^2$ and $u(k) = 0{,}05 \times 10^{-6}\ \text{m}^2$. The experimental setup in Figure 2 is used with the wire whose diameter $a$ is to be checked. The measured width of the central spot for this wire is $L = 8{,}0\ \text{mm}$ with a standard uncertainty $u(L) = 0{,}5\ \text{mm}$. Q.6. Calculate the diameter $a$ of this wire from the model. The standard uncertainty $u(a)$ on the value $a$ of the experimental wire diameter is given, under the conditions of the measurement series, by the following relation: $u(a) = a \times \sqrt{\left(\dfrac{u(k)}{k}\right)^2 + \left(\dfrac{u(L)}{L}\right)^2}$. To decide whether a measurement result is compatible with a reference value, one may use the quotient $\dfrac{|x-x_{ref}|}{u(x)}$ where $x$ is the measured value, $x_{ref}$ the reference value and $u(x)$ the standard uncertainty associated with the measured value $x$. Q.7. Calculate the value of the standard uncertainty $u(a)$ associated with the experimental value of $a$. Q.8. Verify that the measurement result is compatible with the reference value indicated on the spool ($a_{ref} = 0{,}45\ \text{mm}$). Conclude whether or not this wire should be used to build an electric harp. 2. Electrical power supply of the harp: the solar panel Associated with a battery, a photovoltaic solar panel powers the harp electrically. The solar panel consists of photovoltaic cells that convert light energy into electrical energy. We wish to verify the performance of the photovoltaic panel powering the harp and the battery. Data: - Photovoltaic solar panel: • dimensions: 640 mm x 550 mm; • received light power: $P_{lum} = E \times S$ with $E$ the irradiance in $\text{W}\cdot\text{m}^{-2}$ and $S$ the useful area of the converter in $\text{m}^2$; • stated efficiency: 14 %. - Average irradiance during the summer (period of Asian hornet invasion) at the apiary where the harp is placed: $E = 1\ 000\ \text{W}\cdot\text{m}^{-2}$; - Battery capacity: $Q_{batterie} = 18{,}0\ \text{A}\cdot\text{h}$. - Relation between capacity (or amount of charge transferred) $Q$ (in A·h) and transfer duration $\Delta t$ (in h), for an electric current $I$ (in A): $Q = I \times \Delta t$. To verify the efficiency of the photovoltaic panel, the following electrical setup is used: Figure 4 – Electrical diagram of the setup: a photovoltaic solar panel receives an incident light flux. A voltage $U$ is measured across its terminals by a voltmeter connected in parallel. The circuit includes an ammeter in series measuring the current intensity $I$ and a variable resistor $R$; the conventional current flows in the external circuit from the positive terminal of the panel to the ammeter and then the resistor. The current intensity $I$ and the electrical voltage $U$ across the panel terminals are measured. Q.9. Name the phenomenon involved in converting light energy into electrical energy during the operation of the photovoltaic panel and describe it in one or two sentences. Under the summer irradiance conditions of the photovoltaic panel, the maximum electrical power supplied and measured is $P_m = 50\ \text{W}$. Q.10. Calculate the efficiency $\eta$ of the photovoltaic panel. Comment. The electrical energy produced by the photovoltaic panel is sent to a solar regulator which distributes it to the harp and/or to the battery to charge it. The latter powers the harp in the absence of light or when sunlight is insufficient. The electrical current supplied by the photovoltaic panel is $I = 2{,}8\ \text{A}$ under the harp’s sunlight conditions. Q.11. Estimate the charging time $\Delta t_{charge}$ of the battery if all the current intensity coming from the photovoltaic panel is entirely supplied to the battery. Comment on the result obtained. 3. Electronic module The harp’s electronic module contains a capacitor. It is charged under a voltage $U_1 = 1\ 500\ \text{V}$. When a hornet approaches and touches two wires of the harp, the capacitor releases the accumulated energy in a brief instant: it discharges into the Asian hornet, which is then considered as an ohmic conductor of resistance $r$. We aim to recover the value of the capacitor capacitance $C$ in order to determine the energy released to the hornet during the discharge. For this purpose, in the laboratory, using a data acquisition system, the setup shown in Figure 5 is assembled, consisting of the capacitor under study, an ohmic conductor of resistance $R = 2{,}00\ \text{k}\Omega$, an initially open switch and an ideal generator delivering a constant voltage $E = 5{,}0\ \text{V}$. Figure 5 – Electrical circuit diagram: series circuit including an ideal voltage source $E = 5{,}0\ \text{V}$, a switch $K$, a resistor $R$ and a capacitor $C$. The current $i$ flows toward the resistor after the switch is closed. The voltage $u_R$ is indicated across $R$ and the voltage $u_C$ across the capacitor. The charging of the capacitor (initially uncharged) of capacitance $C$ is studied from $t = 0\ \text{s}$, the time at which the switch is closed. The acquisition system then provides the time evolution of the capacitor voltage $u_c(t)$ shown in Figure 6. Figure 6 – Time evolution of the voltage $u_c(t)$ across the capacitor as a function of time: graph of $u_c$ in V as a function of $t$ in µs, from 0 to about 350 µs. The curve starts at $0\ \text{V}$ at $t=0$, rises rapidly in an exponential manner and tends toward a limiting value close to $5\ \text{V}$. It reaches about $3{,}2\ \text{V}$ at about $50\ \mu\text{s}$, $4{,}5\ \text{V}$ at about $100\ \mu\text{s}$, then about $4{,}9\ \text{V}$ at about $180\ \mu\text{s}$. Q.12. Show that the differential equation modeling the evolution of the voltage $u_c(t)$ across the capacitor during charging can be written: $\dfrac{du_c}{dt} + \dfrac{1}{\tau} u_c = \dfrac{E}{\tau}$ where $\tau$ is the characteristic time constant, with $\tau = R\cdot C$. The solution of the differential equation is of the form $u_c(t) = A\cdot e^{-t/\tau} + E$. Q.13. Determine the value of $A$. Q.14. Determine the value of the time constant $\tau$ explaining the graphical method used. Q.15. Deduce the experimental value of the capacitance $C$ of the capacitor. The energy stored $E_{cond}$ in a capacitor of capacitance $C$, subjected to a voltage $U$ across its terminals, is: $E_{cond} = \dfrac{1}{2} \times C \times U^2$. Q.16. Calculate a value of the energy released by the capacitor when a hornet touches the electric harp. Sometimes, the weather does not allow energy production by the solar panel. Nevertheless, the harp’s electronic module always consumes 98,8 J per minute during the day (in the absence of hornets) and 72,1 J per minute at night (because the electronic module is in standby mode). During the beekeeping season when electric harps are used, the average duration of the day is estimated to be 14 h 17 min and that of the night 9 h 43 min. Q.17. Calculate the energy consumed by the electronic module over one day. Compare this energy with that delivered by the capacitor to electrocute a hornet. Data concerning the battery: - Voltage: $U_{batterie} = 12{,}0\ \text{V}$; - Capacity: $Q_{batterie} = 18{,}0\ \text{A}\cdot\text{h}$; - Conversion: $1\ \text{A}\cdot\text{h}$ is equivalent to $3\ 600\ \text{C}$; - Relation between the energy $E$ (in J) stored in a battery, the capacity $Q$ (in C) and the voltage $U$ (in V): $E = Q \times U$. The battery autonomy is about 6 days. It is observed that this device can trap at least 1 000 hornets per day during an invasion period. Q.18. State, justifying the answer, whether the number of electrocuted hornets has a large influence on the battery autonomy. The candidate is invited to take initiatives and present the method followed, even if it did not lead to a result. The method is assessed and must be presented clearly.
⏳ Solution not generated yet

Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.

📝 See the solution

Have a similar exercise? Get it solved step by step, for free.

🧮 Solve my exercise