Solved exercises🧮 Solve my exercise

Baccalauréat 2026 — Physics-Chemistry specialty, Métropole (jour 1) — exercise 1 : Study of a washing machine (official exam paper)

PhysicsLevel : High schoolStudy of a washing machine🌐 Lire en français
Statement
Mastering the duration of the different stages of a washing machine’s wash cycle makes it possible to guarantee effective cleaning while preserving clothes. Each phase—washing, rinsing, spinning—is thus optimized according to the type of laundry, in terms of water consumption, energy consumption, and machine durability. The aim of this exercise is to study the first stages of the operation of a washing machine, namely filling the drum and heating the water, during tests carried out with no laundry inside. 1. Filling the drum The washing machine can be modeled as a rotating drum inside a cubical tank with side length $a$. To regulate the water level in the tank of a washing machine, a pressure switch measures the air pressure in a compression chamber cylindrical in shape and connected to the bottom of the tank: when the water level rises in the tank, part of this water enters the compression chamber and the air trapped inside is compressed. When the pressure reaches a threshold value, the pressure switch sends a signal and stops the filling. In this part, we consider a test of the machine: the pressure switch is then set to allow the tank to be filled halfway. Figure 1. Diagram of the tank and pressure switch of a washing machine: the tank is a cube containing a circular drum shown with dashed lines; the tank is at pressure $P_0$. The water level reaches half the height of the tank, i.e. $a/2$, with air occupying the upper part. On the left, a cylindrical compression chamber connected to the bottom of the tank contains a water height $h$ at the bottom and air at pressure $P$ above it. The pressure switch is connected to this chamber. Point A is located in the tank at the level of the free surface, point B in the compression chamber at the water surface level. Data: - volume of a cylinder of radius $R$ and height $H$: $V=\pi\cdot R^2\cdot H$; - gravitational field intensity: $g=9{,}81\ \mathrm{N\cdot kg^{-1}}$; - density of water: $\rho_{\mathrm{eau}}=1{,}0\times10^3\ \mathrm{kg\cdot m^{-3}}$; - parameters associated with the washing machine studied: the tank is a cube of side $a=60{,}0\ \mathrm{cm}$ and volume $V_c=a^3$; the compression chamber is modeled as a cylinder of radius $r=3{,}0\ \mathrm{cm}$; the pressure of the air in the tank remains constantly equal to atmospheric pressure $P_0=1{,}01\times10^5\ \mathrm{Pa}$; during filling, air and water are assumed to be at the same temperature $\theta_0=20\ ^\circ\mathrm{C}$; the volumetric flow rate $D_v$ of incoming water into the washing machine is $12\times10^{-3}\ \mathrm{m^3\cdot min^{-1}}$. Q1. Express the time $\Delta t_1$ needed to fill the tank halfway in terms of the volumetric flow rate of the water $D_v$ and the side length $a$ of the cube. Calculate numerically $\Delta t_1$, expressed in minutes. The amount of air present in the compression chamber remains constant, as does its temperature. Before filling, the air occupies a volume $V_0=0{,}50\ \mathrm{L}$ and the pressure in the pressure switch is such that $P=P_0$. After filling, the water height in the compression chamber is $h=5{,}0\ \mathrm{mm}$ and the pressure in the pressure switch is such that $P=P_2$. The air is considered to behave as an ideal gas. Q2. Justify why the pressure increases in the compression chamber during filling. Q3. Express the volume $V_2$ occupied by the air in the compression chamber when filling stops, in terms of $V_0$, $r$ and $h$. Q4. Express $P_2$ in terms of the data, then show that the overpressure $\Delta P=P_2-P_0$ between the pressure that caused filling to stop and the initial pressure can be written: $\Delta P=P_0\times \dfrac{\pi\cdot r^2\cdot h}{V_0-\pi\cdot r^2\cdot h}$. It is recalled that, under the test conditions, the water height in the compression chamber is $h=5{,}0\ \mathrm{mm}$. Q5. Calculate the value of the overpressure $\Delta P$ during the test in which filling stops when the machine is half full. Comment on the value obtained compared with that of a normal cycle outside the test, for which $\Delta P=150\ \mathrm{Pa}$. We recall the fundamental law of fluid statics: in an incompressible fluid at rest with density $\rho$, the pressure $P$ at altitude $z$, $P(z)$, satisfies the relation $P(z)+\rho\cdot g\cdot z=\mathrm{constant}$. Q6. Recover the value of the overpressure $\Delta P$ during the test using the fundamental law of fluid statics applied between points A and B in Figure 1. When the machine is no longer in test mode but in normal operation and without laundry, the overpressure $\Delta P$ is $150\ \mathrm{Pa}$. The water height in the compression chamber, $h$, is then considered negligible compared with the water height in the tank. Q7. Determine the volume of water contained in the tank in normal operation and without laundry. 2. Delay duration The timer of a washing machine uses electronic circuits to activate and deactivate the different functions of the washing machine. It is necessary to add a delay between two stages of a cycle to allow time for the machine to stabilize, avoid mechanical shocks, and ensure that each phase starts under good conditions. The aim of this part is to study a simple model of a washing-machine timer using the setup in Figure 2. Figure 2. Diagram of the setup modeling a timer: an ideal voltage generator $E$ supplies, via a two-position switch $K$, a circuit containing a resistor $R$ and a capacitor $C$. Position 1 allows the capacitor to charge; position 2 allows the capacitor to discharge. The voltage $u_R$ is measured across the resistor and sent to a comparator. The setup consists of: - an ideal voltage generator with electromotive force $E=4{,}5\ \mathrm{V}$; - an ohmic conductor of resistance $R$; - a capacitor of capacitance $C$; - a switch K with two positions: position 1 for charging the capacitor and position 2 for discharging the capacitor; - a comparator configured to send a signal ending the delay at the instant $t_{\mathrm{seuil}}$ for which the voltage $u_R$ across the resistor reaches one third of the supply voltage: $u_R(t_{\mathrm{seuil}})=\dfrac{E}{3}$. It is assumed that the comparator does not disturb the operation of the circuit. The circuit can therefore be studied as if the comparator were absent. At the initial instant $(t=0)$, the capacitor being discharged, the switch K is placed in position 1. Q8. Show that the differential equation governing the variations of the capacitor voltage $u_C(t)$ as a function of time is of the form: $u_C(t)+R\cdot C\cdot \dfrac{\mathrm{d}u_C(t)}{\mathrm{d}t}=E$. The solutions of the previous differential equation are time functions of the form $u_C(t)=A(1-e^{-t/\tau})$, with $\tau=R\cdot C$. Q9. Determine the expression for the constant $A$ in the situation studied. Q10. Deduce that the expression for the voltage across the ohmic conductor as a function of time is $u_R(t)=E\cdot e^{-t/\tau}$. Q11. Show that the end time of the delay $t_{\mathrm{seuil}}$, the time at which the comparator sends a signal, is given by $t_{\mathrm{seuil}}=\tau\cdot \ln 3$. The delay duration, denoted $\Delta t_2$, is defined by $\Delta t_2=t_{\mathrm{seuil}}$. To study this delay duration experimentally, the previous circuit is built in the laboratory by replacing the comparator with a data acquisition system. We want to obtain a delay duration $\Delta t_2$ close to 30 s. A capacitor of capacitance $C=4{,}70\ \mathrm{mF}$ powered by a voltage generator $E=4{,}5\ \mathrm{V}$ is used. In addition, several ohmic conductors are available with resistances $R_1=470\ \Omega$, $R_2=5{,}0\ \mathrm{k}\Omega$ and $R_3=100\ \mathrm{k}\Omega$. Q12. Among the proposed values, determine the resistance value of the ohmic conductor to use in order to obtain a delay duration close to the desired one. The electrical circuit is built with the resistance value found in question Q12. The capacitor is charged and the switch is set to position 2, then the evolution of the voltage across the resistor during discharge is observed. The corresponding graph is shown in Figure 3. Figure 3. Evolution of the voltage $u_R(t)$ across the resistor as a function of time: graph of $u_R$ in volt versus $t$ in second, from 0 to 120 s. The curve decreases exponentially from about $4{,}5\ \mathrm{V}$ at $t=0$ toward a value close to $0\ \mathrm{V}$ at $t=120\ \mathrm{s}$. Approximate readable values: $u_R\approx 2{,}7\ \mathrm{V}$ at 10 s, $2{,}0\ \mathrm{V}$ at 20 s, $1{,}2\ \mathrm{V}$ at 30 s, $0{,}8\ \mathrm{V}$ at 40 s, $0{,}5\ \mathrm{V}$ at 50 s, $0{,}3\ \mathrm{V}$ at 60 s, $0{,}2\ \mathrm{V}$ at 75 s, $0{,}1\ \mathrm{V}$ around 100 s. Q13. Determine graphically the initial value $u_R(t=0)$ of the voltage across the ohmic conductor after switching the switch to position 2 and verify that it is consistent with the value of $u_R(t=0)$ obtained by applying Kirchhoff’s voltage law. Q14. Determine, using the graph in Figure 3, the experimental value $\tau_{\mathrm{exp}}$ of the time constant of the RC circuit. Comment. 3. Heating the water After filling the tank and a delay time, the water is heated by an electrical resistor, called an immersion heater, through which an electric current passes. In this part, we consider the heating of the water contained in the tank, from room temperature $\theta_0=20\ ^\circ\mathrm{C}$ to temperature $\theta_f=30\ ^\circ\mathrm{C}$. To model the heat exchanges occurring during heating, we consider that: - the tank is thermally insulated from the outside environment; - the water temperature is uniform. Data: - volume of water in the tank: $V_{\mathrm{eau}}=5{,}7\ \mathrm{L}$; - density of water: $\rho_{\mathrm{eau}}=1{,}0\times10^3\ \mathrm{kg\cdot m^{-3}}$; - specific heat capacity of water: $c_{\mathrm{eau}}=4{,}18\times10^3\ \mathrm{J\cdot kg^{-1}\cdot K^{-1}}$; - electrical power supplied to the immersion heater: $P_{\mathrm{él}}=2\ \mathrm{kW}$, assumed constant. Q15. Name the three possible modes of heat transfer and indicate which one can be neglected during the heating of the water. Q16. Show that the amount of heat $Q$ needed to heat the water from $\theta_0$ to $\theta_f$ is about $0{,}24\ \mathrm{MJ}$. We assume that the electrical power supplied to the immersion heater is entirely transferred to the water in the form of a heat flow $\Phi$ of constant value: $P_{\mathrm{él}}=\Phi$. Q17. Calculate the required operating time of the immersion heater $\Delta t_3$, in minutes, for the water contained in the tank to go from temperature $\theta_0=20\ ^\circ\mathrm{C}$ to temperature $\theta_f=30\ ^\circ\mathrm{C}$. The heat flow $\Phi$ from the immersion heater to the water can be modeled by the relation $\Phi=h_c\cdot S\cdot(\theta_{\mathrm{thermo}}-\theta_{\mathrm{eau}})$, with: - $h_c$: heat transfer coefficient between the immersion heater and the water; - $S$: surface area of the immersion heater; - $\theta_{\mathrm{thermo}}$ and $\theta_{\mathrm{eau}}$: respective temperatures of the immersion heater and the water. Data: - typical heat transfer coefficients between the immersion heater and the water: without water stirring: $h_{c,0}=1{,}0\times10^3\ \mathrm{W\cdot m^{-2}\cdot K^{-1}}$; with water stirring: $h_{c,0}'=4{,}0\times10^3\ \mathrm{W\cdot m^{-2}\cdot K^{-1}}$; - immersion heater-water contact surface: $S=0{,}020\ \mathrm{m^2}$. Q18. Determine the temperatures of the immersion heater with and without water stirring when the water has reached temperature $\theta_f$. During use of the washing machine, a thin layer of limescale can form on the immersion heater. To study its impact on heating, a more advanced model simulates the evolution of the temperature of the water and the immersion heater as a function of heating time. The model is carried out assuming effective stirring of the water. The results of this model are given in Figures 4 and 5 below. Figure 4. Simulation of the water temperature during heating: graph of the water temperature in °C as a function of time in s, from 0 to 200 s. Two curves are shown: “without limescale” (solid line) and “2 mm of limescale” (dashed line). Both start at $20\ ^\circ\mathrm{C}$ at $t=0$. Without limescale, the temperature reaches about $24\ ^\circ\mathrm{C}$ around 50 s, $28\ ^\circ\mathrm{C}$ around 100 s, $32\ ^\circ\mathrm{C}$ around 150 s and $36\text{ to }37\ ^\circ\mathrm{C}$ around 200 s. With 2 mm of limescale, it reaches about $23{,}5\ ^\circ\mathrm{C}$ around 50 s, $27\ ^\circ\mathrm{C}$ around 100 s, $30{,}5\ ^\circ\mathrm{C}$ around 150 s and $34{,}5\ ^\circ\mathrm{C}$ around 200 s. The temperature $30\ ^\circ\mathrm{C}$ is reached around 125 s without limescale and around 145 s with 2 mm of limescale. Figure 5. Simulation of the immersion heater temperature during heating: graph of the immersion heater temperature in °C as a function of time in s, from 50 to 200 s. Two curves are shown: “without limescale” (solid line) and “2 mm of limescale” (dashed line). Without limescale, the temperature increases from about $51\ ^\circ\mathrm{C}$ at 50 s to about $63\ ^\circ\mathrm{C}$ at 200 s. With 2 mm of limescale, the temperature increases from about $96\ ^\circ\mathrm{C}$ at 50 s to about $106\ ^\circ\mathrm{C}$ at 200 s. From Pezzin A., Giansetti M., Ferri A., Comsol Conference Proceedings, 2013. Q19. Using Figures 4 and 5, determine the time needed to heat the water in the case where there is no limescale on the immersion heater, and deduce the temperature reached by the immersion heater at the end of heating. Compare with the value obtained in question Q18. ADEME (French Agency for Ecological Transition) recommends regularly descaling one’s washing machine to avoid excessive energy consumption. Q20. Using Figure 4, show that the presence of limescale on the immersion heater increases energy consumption by about 15 % during the water-heating cycle, compared with a situation where limescale is absent.
⏳ Solution not generated yet

Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.

📝 See the solution

Have a similar exercise? Get it solved step by step, for free.

🧮 Solve my exercise