Baccalauréat 2026 — Physics-Chemistry specialty, Amérique du Nord (jour 2) — exercise 1 : “My feet are cold on the tile floor, I prefer the parquet!” (official exam paper)
Statement
Exercise 1: “My feet are cold on the tile floor, I prefer the parquet!” (11 points)
Although the temperatures of the two floors are identical, one feels colder than the other!
This sensation is related to the effusivity of the materials.
According to Jean-Claude Krapez, research engineer and author of a thesis on the subject:
“The effusivity of a material characterizes the speed at which it can exchange thermal energy with its surroundings. When its thermal effusivity is high, a material rapidly absorbs thermal energy without its surface warming up noticeably (as is the case for stone, steel, tile), and conversely when its thermal effusivity is low the material warms up very quickly at the contact surface with a hot source. This means that this kind of material does not absorb much thermal energy and that this energy remains at the surface, as is the case for wood.”
The contact temperature felt by the foot is determined using the effusivity of the materials in contact.
Illustrative photograph: two feet in socks are each placed on a different floor, one on parquet (wooden slats) and the other on decorated tile.
To reproduce this experiment in the laboratory in order to better understand this phenomenon, a piece of tile, a piece of parquet wood and a silicone pouch are used. The silicone pouch makes it possible to simulate a bare foot because it has mechanical and thermal properties similar to the underside of the foot.
1. Determining the effusivity of a material
Data:
- Effusivity $E$ of a material: $E=\sqrt{\lambda \times c_v}$ with:
$\lambda$: thermal conductivity of the material (in $\mathrm{J\cdot K^{-1}\cdot m^{-1}\cdot s^{-1}}$);
$c_v$: volumetric heat capacity of the material (in $\mathrm{J\cdot K^{-1}\cdot m^{-3}}$).
- $c_v=\dfrac{C}{V}$ with:
$C$: heat capacity of the piece of material used in $\mathrm{J\cdot K^{-1}}$;
$V$: volume of the piece of material in $\mathrm{m^3}$.
- Thermal conductivities of the materials: $\lambda_{\mathrm{bois}}=0,14\ \mathrm{J\cdot K^{-1}\cdot m^{-1}\cdot s^{-1}}$;
$\lambda_{\mathrm{carrelage}}=1,3\ \mathrm{J\cdot K^{-1}\cdot m^{-1}\cdot s^{-1}}$;
$\lambda_{\mathrm{silicone}}=0,80\ \mathrm{J\cdot K^{-1}\cdot m^{-1}\cdot s^{-1}}$.
- Heat capacity of water in $\mathrm{J\cdot K^{-1}}$: $C_{\mathrm{eau}}=m_{\mathrm{eau}}\times c_{\mathrm{eau}}$, with:
$c_{\mathrm{eau}}$: specific heat capacity of water, $c_{\mathrm{eau}}=4,18\times 10^3\ \mathrm{J\cdot K^{-1}\cdot kg^{-1}}$;
$m_{\mathrm{eau}}$: mass of the water in kg.
- $T$: temperature in kelvin;
- $\theta$: temperature in degrees Celsius;
- Variation of the internal energy of an incompressible system: $\Delta U=C\times \Delta T$ with:
$C$: heat capacity of the system;
$\Delta T$: temperature change of the system.
- Reminder: $\sqrt{a}=a^{1/2}$.
Q.1. Show that effusivity has units of $\mathrm{J\cdot K^{-1}\cdot m^{-2}\cdot s^{-1/2}}$.
Since the thermal conductivities $\lambda$ of the materials are given, we aim to obtain the volumetric heat capacities of the materials from a measurement of $C$ and $V$ of the chosen piece.
We choose to determine $C_{\mathrm{carrelage}}$, the heat capacity of the tile piece, by calorimetry.
It is assumed that in a calorimeter, all work and any heat transfer with the outside are neglected.
We place 720 g of water at 25,4 °C in the calorimeter. The tile piece at 39,7 °C is inserted into it. The final thermal equilibrium temperature is recorded after a few tens of seconds, once the heat transfers have taken place. A final temperature of 25,9 °C is recorded.
We consider the system {water + tile} in the calorimeter.
Q.2. Indicate the direction in which heat transfer occurs between the hot body and the cold body.
Q.3. State the first law of thermodynamics and define all its terms as well as their units. Apply the first law of thermodynamics to the system in the calorimeter.
Q.4. Show that the variation of internal energy of the water in the calorimeter is equal to $1,50\times 10^3\ \mathrm{J}$.
Q.5. Deduce that the heat capacity of the tile piece is $C_{\mathrm{carrelage}}=109\ \mathrm{J\cdot K^{-1}}$.
For the study of the heat capacity of the tile, a piece of tile of volume $5,50\times 10^{-5}\ \mathrm{m^3}$ is used.
Q.6. Calculate the value of the volumetric heat capacity of the tile $c_{v\ \mathrm{carrelage}}$.
Q.7. Show that the effusivity of the tile is $E_{\mathrm{carrelage}}=1,60\times 10^3\ \mathrm{J\cdot K^{-1}\cdot m^{-2}\cdot s^{-1/2}}$.
Under the same experimental conditions, $E_{\mathrm{bois}}=0,476\times 10^3\ \mathrm{J\cdot K^{-1}\cdot m^{-2}\cdot s^{-1/2}}$ is measured.
Q.8. Justify the consistency of the effusivity values of the materials with respect to the introductory text.
2. Measurement and calculation of the contact temperature
Data:
- $T(\mathrm{K})=\theta(\mathrm{°C})+273$;
- Effusivities of the materials: $E_{\mathrm{silicone}}=0,756\times 10^3\ \mathrm{J\cdot K^{-1}\cdot m^{-2}\cdot s^{-1/2}}$;
$E_{\mathrm{bois}}=0,476\times 10^3\ \mathrm{J\cdot K^{-1}\cdot m^{-2}\cdot s^{-1/2}}$;
$E_{\mathrm{carrelage}}=1,60\times 10^3\ \mathrm{J\cdot K^{-1}\cdot m^{-2}\cdot s^{-1/2}}$.
To measure the average contact temperature between the silicone pouch heated to about 34 °C (as for a real foot) and a piece of tile (or a piece of wood), whose temperature is first measured, a thermometer is inserted between the tile (or wood) and the silicone pouch.
After a few seconds, thermal equilibrium is reached and the contact temperature is measured. The standard uncertainty associated with each temperature measurement is 0,2 °C.
Principle diagram: a material to be chosen is represented by a horizontal plate. A semicircular silicone pouch rests on the plate. A thermometer is placed at the contact zone between the pouch and the plate; the probe of the thermometer touches the interface. The labels read “Material to be chosen”, “Silicone pouch” and “Thermometer”.
To calculate $T_{\mathrm{calcul.AB}}$, the thermal contact temperature between two materials A and B, the following relation is used:
$T_{\mathrm{calcul.AB}}=\dfrac{E_A\times T_A+E_B\times T_B}{E_A+E_B}$
with $E_A$ and $E_B$ the effusivities of the materials A and B in thermal contact and $T_A$ and $T_B$ their respective initial temperatures in kelvin.
In the case of silicone-wood contact, the initial temperatures are: $\theta_{i\ \mathrm{silicone}}=34,1\ \mathrm{°C}$ and $\theta_{i\ \mathrm{bois}}=19,6\ \mathrm{°C}$, the contact temperature measured between the silicone and the wood, denoted $\theta_{\mathrm{mesure.SB}}$, is established after a few seconds at $\theta_{\mathrm{mesure.SB}}=28,3\ \mathrm{°C}$.
Q.9. Express the value of $T_{\mathrm{mesure.SB}}$ in kelvin.
Q.10. Calculate the theoretical contact temperature denoted $T_{\mathrm{calcul.SB}}$ between the silicone pouch and the wood.
In the case of silicone-tile contact, one experimentally finds $T_{\mathrm{mesure.SC}}=297,2\ \mathrm{K}$ and one calculates $T_{\mathrm{calcul.SC}}=297,4\ \mathrm{K}$.
Q.11. Compare the values of the measured contact temperatures $T_{\mathrm{mesure.SB}}$ and $T_{\mathrm{mesure.SC}}$ with those of the calculated contact temperatures $T_{\mathrm{calcul.SB}}$ and $T_{\mathrm{calcul.SC}}$ and conclude.
Q.12. Explain the reasons for the sensation described in the title of the exercise.
3. Conducto-convective transfer
The cooling inside the foot is studied.
For this, the silicone pouch, pierced up to its center by a thermometer connected to a data-acquisition interface, is immersed in a liquid water/ice mixture, thus constituting a thermostat at 0 °C.
Temperature monitoring lasts three hours, and measurements are taken every 7,2 seconds.
Q.13. Specify what additional heat transfer, linked to the presence of liquid water, appears in the liquid water/ice thermostat compared with the solid materials used previously.
The heat flux between the silicone pouch and the thermostat, in the case of a conducto-convective transfer, is given by Newton’s law; it is written:
$\phi=h_{\mathrm{eau-silicone}}\times S\times (\theta_T-\theta)$, with
- $h_{\mathrm{eau-silicone}}$: conducto-convective transfer coefficient between water and silicone; the larger the conducto-convective transfer coefficient, the larger the flux will be;
- $S$: contact surface between the silicone pouch and the thermostat;
- $\theta$: temperature of the silicone in the pouch and $\theta_T$ the temperature of the thermostat.
Q.14. Give the expression of the heat transfer $Q$ in terms of the heat flux $\phi$ during a very small duration $\Delta t$.
Q.15. Show, by applying the first law of thermodynamics to the silicone, that the variations of the temperature of the silicone inside the pouch can be described by the following differential equation:
$\dfrac{\mathrm{d}\theta}{\mathrm{d}t}+\dfrac{1}{\tau}\times \theta=\dfrac{1}{\tau}\times \theta_T$
with $\tau$ the characteristic transfer time such that: $\tau=\dfrac{C_{\mathrm{silicone}}}{h_{\mathrm{eau-silicone}}\times S}$.
The solution giving the temperature evolution as a function of time has the form:
$\theta(t)=(\theta(0)-\theta_T)\mathrm{e}^{-\frac{t}{\tau}}+\theta_T$.
Document 1 from the appendix to be handed in with the answer sheet: graph showing the temperature of the silicone as a function of time during cooling. The vertical axis is temperature in °C, marked from 0 to 16 °C (major intervals 2 °C). The horizontal axis is time in $\times 10^3\ \mathrm{s}$, marked from 0 to 10. The measured temperature is represented by black crosses, the modelled temperature in °C by gray circles. The two curves decrease exponentially from about 11,6 °C at $t=0$ to about 0 °C between $6\times 10^3$ s and $10\times 10^3$ s; at $1\times 10^3$ s the temperature is around 4 °C, at $2\times 10^3$ s around 1,8 °C, at $3\times 10^3$ s around 1 °C, then it tends toward 0 °C. A box gives the model equation: $\theta(t)=11,6\times \exp\left(\dfrac{-t}{1,04\times 10^3}\right)+16,3\times 10^{-3}$.
Q.16. Compare the two curves obtained in the appendix to be handed in with the answer sheet and comment.
Q.17. Determine the value of the characteristic time $\tau$ by graphical construction to be made on the appendix to be handed in with the answer sheet.
Q.18. Calculate the value of $h_{\mathrm{eau-silicone}}$ knowing that the pouch used has a heat capacity $C_{\mathrm{silicone}}=179\ \mathrm{J\cdot K^{-1}}$ and a total immersed surface area $S=0,0172\ \mathrm{m^2}$.
The conducto-convective coefficient between air and silicone is $h_{\mathrm{air-silicone}}=3,51\ \mathrm{J\cdot s^{-1}\cdot K^{-1}\cdot m^{-2}}$.
Q.19. Compare the values of the two conducto-convective coefficients and indicate the fluid in which the foot cools the fastest.
⏳ Solution not generated yet
Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.
📝 See the solutionHave a similar exercise? Get it solved step by step, for free.
🧮 Solve my exercise