Baccalauréat 2026 — Physics-Chemistry specialty, Antilles Guyane (jour 2) — exercise 1 : Fire safety (official exam paper)
Statement
In establishments open to the public, such as supermarkets, warehouses, or underground car parks, fire safety is a priority. It is therefore essential to put in place measures to prevent and protect occupants and property.
The aim of this exercise is to study:
- a fire alarm siren, which provides a rapid warning to occupants;
- a sprinkler, which is an automatic fire-extinguishing device;
- a fire hose, which makes it possible to bring the fire completely under control.
1. The fire alarm siren
The installation of fire alarm sirens is compulsory in establishments open to the public.
In accordance with standard NFS32-001, the sound signal emitted by a siren consists of:
- sound no. 1 with frequency $f_1 = 544\ \text{Hz}$, for 100 ms;
- sound no. 2 with frequency $f_2$, for 400 ms.
The analysis of sound no. 2 makes it possible to obtain a representation of the variation of its amplitude as a function of time, given in Figure 1. This signal is assumed to be periodic.
Figure 1. Variation of the amplitude of sound no. 2 as a function of time. Graph: horizontal axis Time (s), marked from 1.240 s to 1.247 s; vertical axis Amplitude (arbitrary unit), marked approximately from -15 to +15. The signal is periodic, of distorted square-wave type, alternating between about +15 and -15. Maxima near +15 are observed for intervals close to 1.2400-1.2402 s, 1.2415-1.2425 s, 1.2438-1.2448 s and 1.2460-1.2470 s; minima near -15 are located between these plateaus. The period read between two successive rising edges is about $2.3\times10^{-3}\ \text{s}$.
Q1. Determine the frequency $f_2$ of sound no. 2 and state whether this frequency corresponds to a lower-pitched or higher-pitched sound than sound no. 1.
Figure 2 shows part of the building under study. A siren is mounted on a wall, and the sound intensity level is measured at two points M and N, located at the same distance $d = 5.0\ \text{m}$ from the siren, on either side of an uninsulated partition wall.
Figure 2. Diagram of the part of the building studied: a siren is mounted on the left on a wall. Two uninsulated partitions are shown near the siren; a horizontal partition separates the points N (above) and M (below). Two segments go from the siren to N and M, each labeled $d = 5.0\ \text{m}$.
The sound intensity levels measured at points M and N are respectively $L_M = 92\ \text{dB}$ and $L_N = 67\ \text{dB}$.
Q2. Determine the value of the attenuation by absorption of the sound intensity level between points M and N, denoted $A$, in decibels.
This part of the building will undergo soundproofing work, as shown in Figure 3. The sound from the siren will therefore be more strongly attenuated in some rooms. It will then be necessary to replace the siren with a more powerful one so that the sound intensity level at point N, denoted $L'_N$, is the same as before the work: $L'_N = L_N = 67\ \text{dB}$. The sound emitted by the new siren must then have a sound intensity level $L'_M = 104\ \text{dB}$ at point M.
Figure 3. Diagram of the part of the building studied with soundproofing and the new siren: the siren on the left is replaced by a new siren; the nearby partitions are indicated as insulated; points N and M are still located at $d = 5.0\ \text{m}$ from the new siren, N above an insulated horizontal partition and M below.
According to standard NFS32-001, sirens are divided into classes according to their sound intensity level measured at 2.0 m, as shown in the table in Figure 4.
Figure 4. Sound intensity level of the sound emitted by a siren according to its class. Table: Siren class A, B, C, D. Sound intensity level measured at 2.0 m: A: $< 90\ \text{dB}$; B: from 90 dB to 105 dB; C: from 105 dB to 115 dB; D: $> 115\ \text{dB}$.
Given
Sound intensity levels: $L_2 = L_1 - 20\log\left(\dfrac{d_2}{d_1}\right)$.
- $L_1$: sound intensity level, in dB, at distance $d_1$, in m, from the source;
- $L_2$: sound intensity level, in dB, at distance $d_2$, in m, from the source.
Q3. Calculate the value of the sound intensity level, denoted $L$, measured at 2.0 m, of the sound emitted by the siren to be installed, then determine its class.
2. The sprinkler, an automatic extinguishing device
A sprinkler is a fixed automatic water extinguishing system. It consists of a bulb that blocks the water outlet of a pipe, as shown in the photograph in Figure 5.
Figure 5. Photograph of a sprinkler: a horizontal water pipe is visible; a water outlet is located beneath the pipe and opens when the bulb bursts; the bulb is attached under the water outlet.
During a fire, the increase in temperature causes the bulb to expand and then rupture, thereby triggering water spray over the area to be protected.
The aim of this part is to determine the time required for a sprinkler to activate after the fire has started. This time depends on the ambient conditions present during the fire and on the sprinkler’s own characteristics. Among these, two are essential:
- the rupture temperature of the bulb;
- the Response Time Index, denoted $R_{TI}$ (Response Time Index): the lower it is, the faster the sprinkler bulb bursts in the event of a fire.
In order to determine the Response Time Index $R_{TI}$ of the sprinkler studied, the following experiment is carried out in the laboratory:
- the initial temperature value $\theta_0$ of the sprinkler is measured using an infrared thermometer: $\theta_0 = 22\ ^\circ\text{C}$;
- the sprinkler is placed in a stream of hot air at temperature $\theta_{ext} = 54\ ^\circ\text{C}$ and speed $v = 5.0\ \text{m}\cdot\text{s}^{-1}$ and a stopwatch is started at the same time;
- the temperature $\theta$ of the sprinkler bulb is recorded every 5 seconds using an infrared thermometer to plot the curve in Figure 6.
Figure 6. Variation of the temperature $\theta$ of the sprinkler bulb over time (measurements taken in the laboratory). Graph: horizontal axis Time $t$ (s), from 0 to 300 s; vertical axis Temperature $\theta(t)$ of the sprinkler bulb (°C), from 20 to 60 °C. The curve starts at about 22 °C at $t=0$, increases rapidly, then gradually levels off towards 54 °C. Approximate values: $\theta(25\ \text{s})\approx38\ ^\circ\text{C}$, $\theta(50\ \text{s})\approx43\ ^\circ\text{C}$, $\theta(100\ \text{s})\approx48\ ^\circ\text{C}$, $\theta(150\ \text{s})\approx51\ ^\circ\text{C}$, $\theta(200\ \text{s})\approx52\ ^\circ\text{C}$, $\theta(300\ \text{s})\approx53\ ^\circ\text{C}$.
Q4. State in which direction the heat transfer takes place between the sprinkler bulb and the outside air in the experiment carried out in the laboratory. Justify your answer.
The sprinkler bulb at temperature $\theta(t)$ (in °C) exchanges energy by heat transfer with the outside air at temperature $\theta_{ext}$ (in °C). This heat transfer is modeled by Newton’s phenomenological law:
$\phi = \varepsilon\cdot S\cdot\sqrt{v}\cdot(\theta_{ext}-\theta(t))$
- $\phi$ is the heat flux between the outside air and the bulb in watt (W);
- $\varepsilon$ is a constant in $\text{W}\cdot\text{m}^{-5/2}\cdot\text{s}^{1/2}\cdot{}^\circ\text{C}^{-1}$;
- $v$ is the air speed in meter per second ($\text{m}\cdot\text{s}^{-1}$);
- $S$ is the outside surface area of the bulb in square meter ($\text{m}^2$).
The variation in internal energy $\Delta U$ (in J) of the bulb, with heat capacity $C$ (in $\text{J}\cdot\text{K}^{-1}$), undergoing a temperature change $\Delta\theta$ (in °C), is given by the relation: $\Delta U = C\cdot\Delta\theta$.
Other energy transfers between the bulb and the surroundings will be neglected.
Q5. By applying the first law of thermodynamics to the bulb over a duration $\Delta t$, show that:
$\dfrac{\Delta\theta}{\Delta t}=\dfrac{\varepsilon\cdot S\cdot\sqrt{v}}{C}\cdot(\theta_{ext}-\theta(t))$
The previous relation leads to the following differential equation:
$\dfrac{d\theta(t)}{dt}=-\dfrac{1}{\tau}\theta(t)+\dfrac{\theta_{ext}}{\tau}$, with $\tau=\dfrac{C}{\varepsilon\cdot S\cdot\sqrt{v}}$.
Q6. Solve the differential equation to show that the expression for the temperature $\theta(t)$ of the bulb as a function of time is:
$\theta(t)=\theta_{ext}+(\theta_0-\theta_{ext})e^{-\frac{t}{\tau}}$
Assume that the initial temperature of the bulb is $\theta_0 = 22\ ^\circ\text{C}$ and that it is placed in a stream of hot air at temperature $\theta_{ext} = 54\ ^\circ\text{C}$.
Q7. At time $t = \tau$, calculate the value $\theta(\tau)$ of the bulb temperature.
Q8. Deduce, from a graphical reading of the curve in Figure 6, the value of the characteristic time $\tau$.
The characteristic time $\tau$ (in s) is specific to the experiment carried out in the laboratory. It makes it possible to determine the Response Time Index of the sprinkler, denoted $R_{TI}$ (in $\text{m}^{1/2}\cdot\text{s}^{1/2}$). These two quantities are related by:
$\tau=\dfrac{R_{TI}}{\sqrt{v}}$
where $v$ is the speed of the hot air flow, expressed in $\text{m}\cdot\text{s}^{-1}$. In the laboratory experiment, recall that $v = 5.0\ \text{m}\cdot\text{s}^{-1}$.
Q9. Calculate the value of the Response Time Index $R_{TI}$ of the sprinkler studied.
The sprinkler studied is installed in a warehouse at a temperature of 15 °C. Its characteristics are as follows:
- rupture temperature: $\theta_{rupt} = 68\ ^\circ\text{C}$;
- Response Time Index: $R_{TI} = 90\ \text{m}^{1/2}\cdot\text{s}^{1/2}$.
A few dozen seconds after the start of a violent fire, smoke at a temperature of 200 °C flows around the sprinkler at speed $v_{fumée} = 3.0\ \text{m}\cdot\text{s}^{-1}$.
Q10. Using the solution $\theta(t)=\theta_{ext}+(\theta_0-\theta_{ext})e^{-\frac{t}{\tau}}$ of the differential equation, determine the expression for the time required, denoted $t_{rupt}$, for the sprinkler to activate from the moment the smoke reaches it. Express $t_{rupt}$ in terms of $\theta_{rupt}$, $\theta_0$, $\theta_{ext}$ and $\tau$. Calculate the value of $t_{rupt}$.
The candidate is invited to take initiatives and to present their approach clearly, even if it is incomplete, as it will be assessed.
3. The fire hose
The aim of this part is to study the range of a fire hose whose main characteristics are given in the documentation presented in Figure 7.
Figure 7. Characteristics of the EFF-EUROJET-500 hand-held hose nozzle (from https://www.motopompe-incendie.com). Table: Maximum volumetric flow rate: $500\ \text{L}\cdot\text{min}^{-1}$ (adjustable by rotating ring); Maximum range: 40 m for an inlet pressure of 8 bar; Mass: 1.9 kg; Materials: anodized aluminum, nylon, rubber.
Figure 8. Diagram of the fire hose mounted at the end of the hose. The horizontal hose enters from the left, the nozzle is on the right. Point A is in the hose, with $P_A = 8.0\ \text{bar}$. Point B is at the nozzle outlet, with $P_B = 1.0\ \text{bar}$. Points A and B are at the same altitude on a dashed horizontal line; a vertical axis $z$ is shown on the left.
Given
- the volumetric flow rate of a fluid in a pipe, denoted $D_V$, expressed in $\text{m}^3\cdot\text{s}^{-1}$, is related to the speed of the fluid, denoted $v$, expressed in $\text{m}\cdot\text{s}^{-1}$, and to the cross-sectional area, denoted $S$, expressed in $\text{m}^2$, of the flow pipe by the relation $D_V = S\cdot v$;
- $1\ \text{bar} = 10^5\ \text{Pa}$;
- the fire hose is attached to the end of a cylindrical hose 45 mm in diameter and whose cross-section at point A (Figure 8) is: $S_A = 1.6\times10^{-3}\ \text{m}^2$;
- for steady, incompressible flow of a fluid, Bernoulli’s relation along a streamline between two points A and B is:
$\dfrac{1}{2}\rho v_A^2 + \rho g z_A + P_A = \dfrac{1}{2}\rho v_B^2 + \rho g z_B + P_B$.
$z_A$ and $z_B$ are the altitudes (in m) respectively at points A and B,
$v_A$ and $v_B$ are the speeds (in $\text{m}\cdot\text{s}^{-1}$) respectively at points A and B,
$P_A$ and $P_B$ are the pressures (in Pa) respectively at points A and B,
$\rho$ is the fluid density in $\text{kg}\cdot\text{m}^{-3}$,
$g$ is the acceleration due to gravity: $g = 9.81\ \text{m}\cdot\text{s}^{-2}$;
- water density: $\rho_{eau} = 1\ 000\ \text{kg}\cdot\text{m}^{-3}$.
Q11. Using the expression for volumetric flow rate, show that the speed of the water in the hose at point A is $v_A = 5.2\ \text{m}\cdot\text{s}^{-1}$, when the nozzle flow rate is maximal.
Q12. Using Bernoulli’s relation and the pressure values given in Figure 8, show that the speed of the water at the nozzle outlet at point B is $v_B = 38\ \text{m}\cdot\text{s}^{-1}$.
The motion of the center of mass M of a water droplet of mass $m$ is studied in the terrestrial reference frame assumed to be inertial, with a coordinate system $(O,\vec{i},\vec{k})$ where $\vec{i}$ is a horizontal unit vector directed to the right and $\vec{k}$ a vertical unit vector directed upward, as shown in the diagram in Figure 9. It is assumed that the trajectory of this droplet is the same as that of the water jet.
The initial velocity vector $\vec{v_B}$ of the water droplet makes an angle $\alpha$ with the horizontal.
When the nozzle is tilted, points A and B are no longer at the same altitude: this effect is ignored and the speed of the water at point B is considered to be $v_B = 38\ \text{m}\cdot\text{s}^{-1}$ regardless of the tilt of the nozzle.
The end B of the nozzle is kept at a height $z_B = 1.30\ \text{m}$ above the ground.
Figure 9. Diagram of the situation: a firefighter is holding the nozzle at point B, located at height $z_B$ above the ground. The jet leaves B with an initial velocity $\vec{v_B}$ inclined at an angle $\alpha$ above the horizontal. The trajectory is parabolic and reaches the ground at point P. The horizontal axis $x$ is directed to the right, the vertical axis $z$ upward, and the vector $\vec{g}$ is vertically downward.
Given
- at time $t = 0\ \text{s}$, the center of mass M of the water droplet is located at point B;
- air resistance on the water droplet is neglected.
Q13. By applying Newton’s second law, determine the coordinates $a_x(t)$ and $a_z(t)$ of the acceleration vector $\vec{a}$ of point M.
Q14. Show that the time equations $x(t)$ and $z(t)$ of the center of mass M during its motion are:
$x(t)=v_B\cdot\cos(\alpha)\cdot t$
$z(t)=-\dfrac{1}{2}gt^2+v_B\cdot\sin(\alpha)\cdot t+z_B$
From this, one deduces the equation of the trajectory of point M:
$z(x)=-\dfrac{g}{2v_B^2\cdot\cos^2(\alpha)}x^2+\tan(\alpha)\cdot x+z_B$
The range corresponds to the distance OP in the diagram of Figure 9. It depends on the value of the angle $\alpha$. It will be assumed that, in the situation studied, the range is maximal for an angle $\alpha = 44.7^\circ$.
The equation of the trajectory is then $z(x)=-6.72\times10^{-3}x^2+0.990x+1.30$.
Q15. Determine the value of the maximum range, denoted $x_{max}$. Interpret the difference observed with the value given in the documentation in Figure 7.
⏳ Solution not generated yet
Open this statement in Expert Maths AI: the step-by-step solution is computed on demand, checked by a second resolution, then published here for everyone.
📝 See the solutionHave a similar exercise? Get it solved step by step, for free.
🧮 Solve my exercise